How to fix P0446 code evap. emissions system vent control circuit

code p0446 refers to evaporative emission (EVAP) system--vent control--circuit malfunction===causes wiring--EVAP canister purge valve--ECM
Code p0441 is evap system--incorrect flow detected==causes --hose connections --intake leak--EVAP canister purge valve
replace the purge valve as it is common to both codes
dodge code p1400 is related to a problem EGR system

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction

Why in the world would you replace the canister when the problem is in the vent circuit?

http://ricksfreeautorepairadvice.com/evaporative-emissions-system-primer/

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction. The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP).

https://www.obd-codes.com/p0446

code p0446 refers to evaporative emission (EVAP) system-vent control-circuit malfunction===causes --wiring--EVAP canister purge valve--ECM
code p0455 refers to EVAP system-large leak detected===causes --hose connections--intake leak--EVAP canister---EVap canister purge valve
code p0172 refers to system too rich, bank 1===causes intake blocked---EVAP canister purge valve--fuel pressure ---EGR system---injector/s ---ECM
because the EVAP purge valve appears in all codes I would be inclined to change that unit first the run the fault codes again

P0446 Evaporative Emission Control System Vent Control Circuit Malfunction The code P0446 is set when the engine computer recognizes a fault or restriction at the vent control part of the Evaporative emission control system (EVAP). The description of the fault varies between different car manufacturers, but one thing is common, the code P0446 doesn't directly point to a defective part; some testing might be required to pinpoint the faulty component. What can cause the code P0446: - faulty vent control valve - blockage at the vent hose, vent filter or vent control valve - open or short in the vent control valve circuit - bad charcoal canister - EVAP system leak - faulty EVAP system pressure sensor - bad vacuum switching valve (VSV) - stuck open purge valve (solenoid)

DTC P0446 - Evaporative Emission Control System Vent Control Circuit Malfunction
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. There will be no obvious symptoms to driver, other than MIL illumination.

A code P0446 could mean one or more of the following has happened:
Faulty vent valve
Open, short or excessive resistance on Vent valve control circuit
Blockage of vent valve
Bad PCM


With a P0446 OBD-II trouble code, here are some things to try:
Replace Vent valve
Repair open, short, or resistance problem in control circuit
Repair open, or short, or resistance problem in power circuit
Replace PCM


Hope this helps (remember to rating this free answer and leave us some testimonial comment).

DTC P0446 - Evaporative Emmission Control System Vent Control Circuit
Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test. A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

DTC P0452 - Evaporative emission control system, pressure sensor low imput
DTC P0453 - Evaporative emission control system, pressure sensor high imput

The PCM monitors the EVAP control system FTP sensor input signal to the PCM. The test fails when the signal average jumps above a minimum allowable calibrated parameter. If both codes are present, it sounds like your fuel tank pressure sensor has failed.

The sensor is on top of the tank and you will have to remove the tank. But your symptoms are pointing to more than just the sensor. You may have wiring problems.


Hope this helps (remember to rate and leave a comment about this free answer).

Hi, your vent valve has malfuntioned. The vent valve is near the tank, and has a hose to the tank and a solenoid to close it. Check the wiring/connector. If OK, try applying 12 volts directly to the solenoid. If it does not click when voltage is applied, replace the solenoid/valve.

P0446 Evaporative Emmission Control System Vent Control Circuit OBD-II Trouble Code Technical Description

Evaporative Emission Control System Vent Control Circuit Malfunction
What does that mean? Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.
Symptoms There will be no obvious symptoms to driver, other than MIL illumination.
Causes A code P0446 could mean one or more of the following has happened:

• Faulty vent valve
• Open, short or excessive resistance on Vent valve control circuit
• Blockage of vent valve
• Bad PCM

Possible Solutions With a P0446 OBD-II trouble code, here are some things to try:

• Replace Vent valve
• Repair open, short, or resistance problem in control circuit
• Repair open, or short, or resistance problem in power circuit
• Replace PCM

P0446 - Evaporative Emmission Control System Vent Control Circuit

Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.

Causes: A code P0446 could mean one or more of the following has happened:
* Faulty vent valve
* Open, short or excessive resistance on Vent valve control circuit
* Blockage of vent valve
* Bad PCM

Possible Solutions: With a P0446 OBD-II trouble code, here are some things to try:
* Replace Vent valve
* Repair open, short, or resistance problem in control circuit
* Repair open, or short, or resistance problem in power circuit
* Replace PCM

I hioe this helps to solve it.

P0446 - Evaporative Emission Control System Vent Control Circuit Malfunction

Evap vent valve has only one purpose. It closes in order to seal the vent so the EVAP system can pressurize and ensure there are no leaks. Evap vent valve is usually supplied Batt. voltage with key on. The ECM's driver controls the ground, and when grounded, activates the valve (closing it). If the ECM detects a short to ground, and open,or a short to battery voltage on the control circuit, P0446 will set. Code also may refer to ECM detecting that EVAP system is unable to achieve or maintain vacuum during test.

Symptoms: There will be no obvious symptoms to driver, other than MIL illumination.

Causes: A code P0446 could mean one or more of the following has happened:
* Faulty vent valve
* Open, short or excessive resistance on Vent valve control circuit
* Blockage of vent valve
* Bad PCM

Possible Solutions: With a P0446 OBD-II trouble code, here are some things to try:
* Replace Vent valve
* Repair open, short, or resistance problem in control circuit
* Repair open, or short, or resistance problem in power circuit
* Replace PCM

I hope help with this (remember to rate and comment this).