Question about 1996 Ford Taurus

3 Answers

Front end shakes bad when I brake

When you apply preasure to the brakes the whole front end shakes. I've replaced tie rod ends, lower ball joints, sway bar links, struts and strut ends, and the warped brake rotors. It doesn't shake as bad now but the problem hasn't been fixed. I'm at a loss, what should I do. I can't afford to take it to a shop and i've alredy spent so much time and money.

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 79 Answers

You May Have A Bad Hub Bearing, Make sure The hub is Completely Free of Rust The rotors Must Have A Clean Surface To Assure No Runout.

Posted on Apr 23, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Sounds like air in the brake lines one side braking before the other side

Posted on Feb 11, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,004 Answers

My dear if according to you,

You've replaced tie rod ends, lower ball joints, sway bar links, struts and strut ends, and the warped brake rotors and the issue is still at hand; then you ought to consider replacing the hubs.

Good luck.

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ball joint bolt fell out upper in 2007 GMC Envoy


Upper ball joint? That's not related to the job of replacing a tie rod or tie rod end. It's also not related to the brake job.

It's an '07 and it had a bolt-in ball joint? That's not factory - it's been replaced before.

Aug 07, 2014 | 2007 GMC Envoy

3 Answers

Front end shakes,tie rod and upper ball joints have been replaced


Very little info for a fix. Tie rod and upper ball joints do not make a front end shake. Lower ball joints wear out before the uppers do.
Front end shakes at what speed, if you have a broken belt in one of your front tires you will notice it more at low speeds. Mud or snow stuck in wheel will make them vibrate at speed. Lug nuts tight since front end work? You need to give more info. Switch front tires with back tires. If shake is in steering wheel it more than likely is front end but if you feel it in your seat it is more than likely in the rear of the car.

Jan 09, 2012 | 1999 GMC Jimmy

2 Answers

My 93 lebaron 4 door has a shake int the front end and all the ball joints, tie rod ends, control arm bushings, and cv shafts are tight.


Does it pull to one side? Could possible be warped rotors, or a bad caliper.

Does it shake all the time even when braking, or only when braking? High speed or low?

May 02, 2011 | 1993 Chrysler Lebaron

1 Answer

I have a knocking as i do long left hand turns from the front nearside of the car (2003 x type jag) worse if someone sat in passenger seat


There are several components that could cause noise from the front when turning. I am assuming when you say the Front nearside you are saying the fromt left wheel is where the knocking is comming from when making a left turn. The components to be concerned about are, Wheel bearings, Ball Jionts, Tie rod Ends, CV joints and brake rotors.
Wheel Barrings:
Jack the car up under the control arm until the wheel is off the ground about 3 inches. Slide a pry bar ybder the tire and place the other hand on the top of the tire. As you lift and lowere the pry bar fell for loose movement in the tire. If there is such movement you have a bad wheel bearing.
Ball Joint:
Repeat the test above and watch the upper and lower ball joints for movement. Is there is movement replace the bad ball joint.
Tie Rod ends:
With the tire still off the ground grip the tire in the front and back and rey to move it as if your were trying to turn the tire. Watch the tie rod ends for loose movement. If they are loose replace them.
CV joint:
The Joint is housed in a rubber boot. If you can feel the joint inside the boot you can turn the tire forward and back and feel for play in the joint. If you are not able to feel the play you can loosen the clamp on the boot and push the boot out of the way. Then repeat the test.
Brake Rotors. Inspect the brakes for wear and any signs of pitting or grooves in the rotors.
You need to take this seriously because if you have a Ball joint or tie rod end break while driving, it will cause a wreck.

Apr 04, 2011 | 2003 Jaguar X-Type

1 Answer

My car is shaky every time i hit a stop light?


you should keep all four tires on the ground !!!! LOL ! your rotors or brake pads are bad. do you feel it shake in the steering wheel ? Check these three items and im sure it will fix.......1) jack front car up and try to move front tires in all directions, does it feel loose at all? if yes check tie rod ends, upper and lower ball joints. 2) check brake pads for wear, heat from pads warp the rotors and cause the break pedal and steering to shake or vibrate. 3) If nothing can be found wrong with the tie rods or ball joints i recommend changing the rotors and brake pads, a pretty cheap fix.

Jan 21, 2011 | 2005 Dodge Neon

1 Answer

Replacing a front wheel bearing


here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation
  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Apr 17, 2009 | 2003 Chrysler PT Cruiser

2 Answers

Front end shakes


check the tie-rod ends, control arms and antiroll bars are all secure.

May 27, 2008 | 1983 Ford Fairmont

Not finding what you are looking for?
1996 Ford Taurus Logo

749 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...