Question about Mazda Cars & Trucks

Open Question

What is the Tappet Clearance 1994 Mazda B1800

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 84 Answers

SOURCE: valve clearance

Hello, For all 615, 616 (4cyl) and 617 (5cyl) through 1985 model year is:
cold intake 0.10mm or .006in
exhaust 0.35mm or .014in
hot intake 0.15mm or .007in
exhaust 0.40mm or .016in
CYA, Gator241

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: Valve tappet adjustment

well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Posted on Feb 07, 2009

  • 88 Answers

SOURCE: need to check tappet clearance on car

forget book set intake at 10 exhaust same use 20/50 oil hey vote for me ok

Posted on May 26, 2009

  • 608 Answers

SOURCE: how to measure tappet clearance with dial gauge

When setting tappets, it has to be born inind that the valve stem wears an indentation into the face of the rocker. This prevents a really accurate tappet adjustment, so the customer is right again. If you do not posess a tappet setting dial gauge, a normal engineers dial gauge will do just as well. The procedure is the same as using your feeler gauge except that you set the dial gauge up on the cylinder head with the pointer resting on the head of the rocker. Press down fairly firmly on the rocker valve end and zero the gauge. Next lift up on the rocker and read off the clearance, from the gauge, Use a magnetic base to support your gauge and repeat the pocedure for each valve pair.

Posted on Mar 25, 2010

cansmo
  • 2431 Answers

SOURCE: valve clearence settings mazda protege 2003

This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Posted on Feb 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What is the valve clearance of mazda 323 1.3 engine 94 model


manual adjustment ? then 12th inlet and 15th exhaust will suffice

Mar 12, 2015 | 1994 Mazda 323

1 Answer

Mazda 6.2 engine valve clearance


tappet clearance for this engine i wouldnt know offhand but 12 inlet and 14 exhaust will suffice without doing any damage and 25th for the plugs

Apr 15, 2012 | Mazda Cars & Trucks

1 Answer

Valve clearence settings mazda protege 2003


This is for a non turbo2_24_2012_5_45_49_am.gifNew adjustment shim =Removed shim thickness+ measured valve clearance- STANDARD VALVE CLEARANCE (0.26 mm or 0.010 inch)

Feb 24, 2012 | Mazda Protege Cars & Trucks

1 Answer

How to measure tappet clearance with dial gauge


When setting tappets, it has to be born inind that the valve stem wears an indentation into the face of the rocker. This prevents a really accurate tappet adjustment, so the customer is right again. If you do not posess a tappet setting dial gauge, a normal engineers dial gauge will do just as well. The procedure is the same as using your feeler gauge except that you set the dial gauge up on the cylinder head with the pointer resting on the head of the rocker. Press down fairly firmly on the rocker valve end and zero the gauge. Next lift up on the rocker and read off the clearance, from the gauge, Use a magnetic base to support your gauge and repeat the pocedure for each valve pair.

Mar 25, 2010 | 1988 Mitsubishi Cargo

1 Answer

WHAT IS THE TAPPET CLEARANCE FOR NISSAN GA 15 CARBURATED,INTAKE AND EXHAUST?


what is the tappet clearance setting for the ga15 nissan sunny
i need help to know the clearance of intake and the exhaust valve.

Nov 02, 2009 | Nissan Sentra Cars & Trucks

1 Answer

Tune up Mazda 6


the owner of the car should be able perform engine tune-up . Prepare the tune up tools and materials . so that when tune-up is performed ,engine should be on peak performance and within specification.Use multi tester , Use timing light,use dwall meter ,use tachometer ,use feeler guage, adjust spark plug and contact point gaps. Adjust Idle speed and Idle mixture. Adjust tappet clearance,observe safety rules.If the owner of the car cant do the job done because of work then the owner of the car should go to a car mechanic and let them tune-up the engine.

Oct 02, 2009 | 2004 Mazda 6

2 Answers

TAPPET SETTINGS HONDA PRELUDE 2.2 IMPORT


Intake valve clearance 0.15mm-0.19mm (6-7 thou); Exhaust clearance 0.17mm-0.21mm (7-8 thou). All measurments COLD engine. 2.2 VTEC Prelude engine 1992-1996, import and UK.

Feb 22, 2009 | 1994 Honda Prelude

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...