Cars & Trucks Logo

Related Topics:

D
Dean Scott Posted on May 27, 2017

2008 dodge caliber stalls when put into gear

Happens after restart on warm engine

5 Related Answers

Anonymous

  • 12 Answers
  • Posted on Mar 12, 2009

SOURCE: windshield wipers 2008 dodge caliber

Go take it to the dealer you should still have a full warranty. If you want to try and do it your self you could void that warranty.

Ad

Anonymous

  • 1 Answer
  • Posted on Mar 25, 2009

SOURCE: Vibration when in gear, and stalling.

The problem is the torque converter solenoid. I had it happen on my 94 Cavalier a few years back and was a cheap fix at the local car mechanic. What happens is the transmission warms up and hits a certain speed where the solenoid engages, but then it sticks and won't disengage until it cools down sufficiently. When it sticks, it causes the car to shake when slowing down and will snub out the engine if you come to a stop.

Anonymous

  • 77 Answers
  • Posted on Apr 29, 2009

SOURCE: 1999 olds alero stalls when put in gear

Runs fine when not put in gear? Sounds like transmission is stuck in "lock-up". Need to go to transmission or full automotive shop for repair. This is not something you want to attempt on your own unless you are experienced with removing valve bodies and solenoids from the inside of transmissions.

Anonymous

  • 62 Answers
  • Posted on May 10, 2009

SOURCE: Car hesitates/stalls when engine is warm and car starts to move.

Sounds like a bad motor mount, pop the hood and see if the motor shakes or moves rapidly when u put it in gear holding down the brake.

Anonymous

  • 2559 Answers
  • Posted on Jun 01, 2009

SOURCE: 2007 Dodge Caliber will not start

Yes,They usually fail that quick

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Dodge Caliber. Can I get the right side window fuse allocation please?

Question edited for clarity.

Dodge Caliber (2006-2012) fuses

Fuse Box Diagrams https://fuse-box.info > dodge > dodge-caliber-2006-20...
Fuse box diagram (location and assignment of electrical fuses) for Dodge Caliber (2006, 2007, 2008, 2009, 2010, 2011, 2012).

Dodge Caliber fuse box and relays diagrams

StartMyCar https://www.startmycar.com > dodge > caliber > info > f...
Dodge Caliber fuse box and relays diagrams. Explore interactive fuse box and relay diagrams for the Dodge Caliber. Fuse boxes change across years, ...

Layout of the fuse box ' Page 2

Dodge Caliber Forum https://www.caliberforumz.com > threads > page-2 Every Caliber has the fuses listed in the Owner's Handbook Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine .

..
1helpful
1answer
0helpful
2answers

2008 Dodge Caliber. Is there a fuse for the alternator?

There are two fusible links. See arrachment.
8_15_2023_3_34_40_am.jpg
0helpful
1answer

What could issue be when caliber starts fine but dies when put in gear?

it is obvious that under a load the car will not run
first do a tune up and make sure all cylinders are firing,check codes and even do a fuel pressure check
0helpful
1answer

2008 dodge caliber engine diagram

There is a Dodge website (not from the corporation, but from fans) for Dodge vehicles and they have a subsection on the Caliber. There is a 2007 or a 2008 service manual online there if you join their group. good luck.
0helpful
1answer

Gear shifter stuck in park on 2008 dodge caliber

the brake light switch control the shifter. replace the brake light switch.
0helpful
1answer

2008 Dodge caliber. 1.8 sxt. I have 4 error

disconnect the battery for 10 minutes and try to reset the codes.
0helpful
1answer

Symptoms the neutral switch is defective on a dodge calliber

Maybe a shift cable adjustment

Sounds like that may effect the
trans gear position sw,not the neutral
safety & the car shuts off

When it was jumped it was in a position that
it should be & started on time
6helpful
1answer

How do I change spark plugs on a 2008 Dodge caliber

easy there may be a cover over he engine which just lifts off, then you need a selection of torx bits to remove the screws that holt the coils 1 for each coil disconnect the electrical connector on the coil and remove the coil pulling straight up then ysing a 5/8 spark plug socket remove th eplugs and install the new plugs put back the coils and go
2helpful
1answer
Not finding what you are looking for?

485 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...