At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There should be T10 screws coming through the bottom to the top cover. It is easier to remove the clam shell with the steering wheel removed, but not necessary.
The headlight switch is part of a muti-switch the runs the lights on one side and wipers on the other. They are not cheep.
1) remove air bag
2) remove steering wheel
3) remove steering colum covers
4) unplug multi- switch (there may be 2 screws that hold the plug to the colum
5) remove screws (I think there is 4 screws) that hold multi-switch
6) remove muti-switch. (there may be a ty-wrap or wire harness holder you will need to free the wires from)
7) reverse order to reinstall
remove the steering colum covers were the cyn is look at about 3 o clock theres a small hole turn key to on insert a pick into the hole and push while turning the key and pull out.
Remove the steering wheel, turn signal reset (plastic), remove clip and spring. Remove trim to expose the entire colum. Disconnect all connectors. There are four main bolts holding the colum up. Remove the bolts and lower the colum. At the end of the steering shaft there is a bolt going through the colum. Remove the bolt. The colum can then be removed.
get a phillipshead un do about 4 screws from underneath plastic cover which hides steering colume. remove cover you will see white plug on the left hand side of ignition barrel disconect.then right hand side there will be acable disconect.now get a small chissel and anti clockwise tap bolts which have no heads on them that are on top of steering colume when they are alittle bit lose use plyers its easier pull bolts out clamp will then come of and then you can pull whole ignition of. now there is 2 brass pins which hold barrel in ignition up near the key end remove and barrel will come out but it might be easier to take whole ignition to locksmith and get them to do it and get new key for around 30 bucks i did a mates about couple months ago seeya orangepeel.
Replace your headlight switch. You need torx bits, a steering wheel puller, and bolts to perform the repair.
Disconnect your negative battery cable and wait at least 1 minute before going any further (this insures your airbags are disabled if your vehicle has them).
Remove the plastic covers that cover the steering colum. If applicable, remove the airbag from the steering wheel; if you don't have a airbag pull the horn switch from the center of the steering wheel. Remove the retaining clip from the center shaft in the steering colum. Remove the bolt that holds the steering wheel, then use a steering wheel puller to remove the steering wheel. Remove the torx screws from the headlight switch, and remove the electrical connectors. Install in reverse.
I hope this information helps you, and I wish you luck on your repair.
First disconnect your negative battery cable. Then remove the plastic cover below your steering colum, and the covers that cover your headlight swith, turnsignal switch, ignition, ect. Remove the bolts that hold the steering colum to the dash, and allow it to lay on the drivers seat. Place a towel under the colum (to catch metal shavings), and drill out the two screws that hold the ignition in place.
Install your new ignition in reverse.
if the fuse is good then the multifunction switch is bad. this is the switch in the steering colum. this switch comes with the signal arm that comes out the side of steering colum as a complete assembley. the top and bottom covers of the steering colum must be removed to change switch.
×