Question about Mazda CX-7

1 Answer

Mazda CX7 front bumper removal

How to remove font bumper on Mazda CX-&

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Start with the small screws on the bottom, then take off the splash shields running in front of the tires. open the hood and pop the center out of the two big clips by the headlamps, the two big Philips screws on the rad support and finally get someone to help you pull it off. Slowly start from one side and make sure to unplug all of the lights before any tension gets on them. have some carboard or a tire ready to place it on without scratching it

Posted on Jul 14, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: replacing front bumper of mazda mx5

It should only need little plastic pins and screws. You could get these at Auto Zone or another auto part store near you.

Posted on Mar 31, 2009

  • 580 Answers

SOURCE: how to remove front bumper to fit lower fog lamps

Why not Jack up front of car, Remove front wheels if you need additional room & fit them from under the car

Posted on Jul 13, 2009

Hrnsly
  • 154 Answers

SOURCE: Timing chain broke on a 2007 cx7 w 65K miles

you need to take it to your local dealer and raise a big fuss because this is a known problem and if you yell loud enough you should be able to get this fixed under warranty.

Posted on Aug 12, 2009

  • 617 Answers

SOURCE: I have an 02 Mazda Tribute with a leaking Radiator

1. Drain coolant
2 Remove lower splash shields
3. Disconnect the lower radiator hose and the high pressure transaxle line
4. Lower the vehicle
5. Disconnect the transaxle return line
6. Disconnect the upper radiator hose and degas hose
7. Position the hood latch assembly out of the way
8. remove the 2 bolts and the center support
9 remove the 2 top bolts retaining the cooling fan to the radiator
10. remove the upper radiator support brackets, and remove the radiator from the vehicle
11. To install, reverse the removal procedure

Posted on Feb 07, 2010

  • 2 Answers

SOURCE: Remove 2003 MAzda 6 parking light bulb

http://forum.mazda6club.com/electrical/135367-changing-194s-headlights.html

Posted on Feb 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the entire headlight assembly on a 2008 Mazda CX 9.


There are a few installation bolts that are accessible from the top and side but you will need to remove the entire front bumper to access two of the lower ones. Here are some pics from the factory manual. First shows location of the headlight bolts and fasteners. Others show how to remove the bumper. 10mm socket should handle all the bolts you need to remove. Disconnect the battery prior to starting and headlights off. HID headlight voltage is around 25,000 volts so you want to ensure no power to the system before performing repairs.
25934749-fb0dbpuz0qoml01jiatehqdr-5-0.jpg

25934749-fb0dbpuz0qoml01jiatehqdr-5-2.jpg

25934749-fb0dbpuz0qoml01jiatehqdr-5-5.jpg

Oct 31, 2015 | 2008 Mazda Cx 9

1 Answer

Replace outer front door handle Mazda cx7 2010 model


Hey, I just use a metal zipstrip. Cheap and easy. Look on youtube for Prizm handle replacement. You basically slip it under the current handle and slip it in the zip buckle to make a loop. It's ghetto but works and does not use duct tape unlike most Red Green type "solutons".

Feb 01, 2015 | 2010 Mazda CX-7

1 Answer

Replacing struts on Mazda CX7


There are 3 Nuts inside the Engine Compartment, There is one Bolt on the Lower Arm and you have to remove the ABS and Torsion Rod. You need a Spring Compressor to do this job.

Apr 15, 2013 | 2007 Mazda CX-7

1 Answer

How do i replace a headlamp on a 2007 mazda cx7


un plug the cable socket at the back side of the headlight then remove the rubber cover at the same place and then there is a steel wire clip carefully remove it (as you have to put it back again) the lamp can be removed easily you have to put the new one in the same direction again so remember what you remove

Jan 20, 2011 | 2007 Mazda CX-7 Grand Touring

1 Answer

I cannot remove the push pins in the wheel weel on my Mazda CX7. Any suggestions? They have a philips screw head but unscrewing does nothing.


TRY TO PRY WITH A FLAT SCREWDRIVER BETWEEN THE SCEW AND WASHER DURING YOU UNSCREW THE PHILLIPS ...IT SHOULD BE OK....

Dec 04, 2010 | 2007 Mazda CX-7 Grand Touring

2 Answers

How do I change the bulb in the low beam headlight in my 2007 Mazda CX7?


Removing the bulb in a CX7 is a real PITA. If replacing the right bulb, turn the steering wheel all the way to the right, or do the opposite for the left side. (or you can opt to remove the entire wheel on the corresponding side) You'll need to remove 3-4 of the fender well clips with a phillips screwdriver being careful not to break them. Once the screws are removed, pry back the wheel well cover to access the back of the headlamp to change the bulb.

Nov 04, 2009 | 2007 Mazda CX-7 Grand Touring

1 Answer

I am trying to replace the low beam bulb on the passenger side of a 2007 Mazda CX7 . Can't seem to figure out how to get to it. Any help?


Open the 2007 CX-7 Owners Manual (here is you don't have one http://www.mazdausa.com/MusaWeb/pdf/manuals/2007CX7OM.pdf)
Go to page 8-35 (P. 331 in the pdf). Close the hood, you're in the wrong place. Remove the cover in the front of the wheel arch to expose the headlight assembly.

Jun 08, 2009 | 2007 Mazda CX-7 Grand Touring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

631 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...