Question about Cars & Trucks

Open Question

1989 mack midliner cs200

What can i do to find a water pump for my Mack truck?

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 120 Answers

SOURCE: will a modulator valve mack my transmission slip


Posted on Nov 18, 2009

  • 85 Answers

SOURCE: I have a chevy avalanch pickup truck and it make

take off belt and try again onely for less than 5 min to see if it still makes noise

Posted on Feb 27, 2010

  • 14585 Answers

SOURCE: mack truck is not

Most of the injector pumps are direct drive, gear to gear. If you are only getting fuel from one line then the shaft in the injector pump has sheared.. Though it is a very slight possibility that the gear has sheared off some of there teeth, very slight. You'll know when you start tearing it apart.

Posted on Feb 07, 2011

  • 17970 Answers

SOURCE: I am dealing with a

Any dealer should be able to print this out for you. Go into the parts department with your exact model and vin, and tell them what you need. In knoweled cases, the arrangement number they came up with for one of my customers 1994 CH613 trucks was 17MS727P2, although yours might vary slightly. The internal name for this assembly is "ELEC EQUIP INT-BASIC"

Other posibilitie could be search in

Hope this helps, good luck.

Posted on Sep 24, 2011

  • 76682 Answers

SOURCE: wiring diagrams 2000 mack 612

Factory vehicle OEM service manuals and wiring diagrams

I am sorry but I regret to say that doesn't have any wiring diagrams available for free downloading due to copyright laws. You can however gain access to the factory service manuals and wiring diagrams and all factory service letters at this site for a modest subscription fee I am told.

Posted on Jun 28, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Just had a new p.t.o to a 07 mack vison it wont lift the tipper so i fitted a dummy hose the p.t.o engages and does pump but very slowly im talking like under 20litres a minute?

if you have a mack tri shaft box then check that the pto pump has been fitted to the correct hole. Some pto pumps run directly onto the counter shaft and others use an adaptor to increase the pump rpms or run from a larger gear in the box that runs the pump at higher rpms. . I suspect that the installation of the pump is incorrect and not in accordance with the fitting instructions for the pump.
Pto pumps fitted to road ranger box can be either on the side or underneath and each position connects with a different gear to drive it.

Feb 26, 2015 | Cars & Trucks

1 Answer

Where is the mc manual switch on 2000 mack truck

Call mack. Their tech people or parts people should be able to direct you.

Feb 12, 2015 | Cars & Trucks

1 Answer

No, Its a semi old Mack. Rear lights wiring diagram. Why do they come on and go off?

bad connection - check for corroded contacts on connectors or bad ground

Dec 17, 2014 | Cars & Trucks

1 Answer

I am looking for a free fuse box diagram for a 98 mack truck

This question has been asked here before, except for a 95 model. The advice given is still sound.

Dec 07, 2014 | Cars & Trucks

1 Answer

Jake brake installation 1999 Mack truck

This is a specialist operation and should be done by competent mechanics. If it is a Mack engine any wrong installation will result in cam follower/cam shaft damage

Nov 03, 2014 | Cars & Trucks

1 Answer

Spark plug wire to distributor cap diagram 291 mack truck 1961

If you haven't removed the wires yet don't. The best way to replace ignition wires is to remove ONE at a time and replace with a new one before moving on to the next. That way you won't get the firing order mixed up. Hope this helps

Oct 11, 2014 | Cars & Trucks

2 Answers


if you have cold weather its a tire pressure code that may take days to go away

Jul 15, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

Where is the thermostat in a 1989 mack dump truck

There are inline thermostats, and there are serviceable thermostats that are in a housing on the end of the cyl head.

Jun 18, 2013 | Cars & Trucks

1 Answer

The electric fuel pump isn,t coming it the inertia switch

ford has a problem with the inertia switch check to mack sure the switch is reset u can thump it with a screw driver handle not real hard and that will trip it then push it in to reset it and while your doing things with the switch pull the conecter off and lool at if its burned or melted that will cause no power to go throu it i had the same problem with a ford ranger. if your sure that no fuses or relays are bad and that the switch is working properely then the pump is bad.

Dec 04, 2010 | 1989 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides