Where is the evap canister located on 08 saturn outlook

Usually the canister is alongside the fuel tank at the rear of the car. Sometimes vents into the fuel filler pipe.

In the 2008 Kia Sportage, the purge evacuation (EVAP) solenoid is typically located near the charcoal canister. The exact location may vary slightly depending on the specific engine configuration and optional equipment, but here is a general guideline:

1. Locate the Charcoal Canister: The charcoal canister is a component of the EVAP system and is responsible for storing fuel vapors. It is usually located in the rear of the vehicle, near the fuel tank or in the engine compartment. The canister is a cylindrical or rectangular-shaped container.
2. Find the EVAP Solenoid: Once you have located the charcoal canister, look for a smaller component connected to it. This component is the purge evacuation (EVAP) solenoid. It is typically a small plastic or metal device with electrical connectors and vacuum hoses.
3. Follow the Hoses and Wires: Trace the vacuum hoses and electrical wires connected to the charcoal canister to locate the EVAP solenoid. The solenoid may be connected directly to the canister or positioned nearby.

Please note that the exact location of the EVAP solenoid may vary slightly depending on the specific engine and emission system layout of your 2008 Kia Sportage. Consulting the vehicle's service manual or contacting a Kia dealership may provide more accurate and detailed information tailored to your specific model.
It's important to exercise caution when working with the EVAP system and its components, as they are part of the vehicle's emission control system. If you are unsure or uncomfortable performing the task yourself, it's recommended to seek assistance from a qualified technician or a reputable automotive service center. They have the expertise and tools to locate and service the EVAP solenoid properly.

The canister is under the car near the gas tank. But hold on that may not be the problem.
A code P0440 could mean one or more of the following has happened:

• The gas cap is not installed or working properly
• The purge solenoid has failed
• The canister is plugged and not working properly

I have Saturn vue 2008 try to take it off transmission fluid

How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...

Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube

Trouble Code: P0446

Evaporative Emissions (EVAP) Vent System Performance

Possible Causes:


The EVAP system tests run when the engine is first started and meets the Conditions for Running the DTC. An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill condition.An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission (EVAP) Canister Filter Replacement and Evaporative Emission (EVAP) System Cleaning .Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system.Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.For intermittent conditions, refer to Intermittent Conditions .

Purge solenoid is going to be near the evap. canister...or attached to it via a hose. It will have an electric solenoid with a two wire connector. Most newer cars are under the rear of the vehicle near the fuel tank or just near the bumper. the evap. canister is probably going to be rectangular in shape.

Evaporative Emission (EVAP) Canister Purge Soleno Evaporative Emission (EVAP) Canister Purge Solenoid Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.id Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.