Question about Cars & Trucks

Open Question

How to replace camshaft sensor bank 2 on 2000 bmw x5 4.4i

How to replace and locate

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 43 Answers

SOURCE: P0344 Camshaft Position Sensor A Circuit Intermittent (Bank 1 or

The camshaft sensor is located right above the crankshaft pulley on the passengers side of the front cover of the engine. It will be a 3 pin sensor either gray or black in color. There is a pointer that is attached to the sensor and it is either gold or silver in color. There is also a recall out on this camshaft sensor. If the color of the sensor is black then it should qualify for the recall. If you get in touch with a Ford dealer they should be able to help you with your recall if the sensor is black since it is a safety recall. As far as your exhaust pressure sensor it is located on the front of the engine right by the heater core hose a little to the passengers side of the center of the front of the engine. there will be a tube attached to the bottom of the sensor that goes from it to the front of the exhaust manifold on the very front of the passengers side exhaust manifold.

Posted on Apr 11, 2009

  • 14036 Answers

SOURCE: Camshaft position sensor replacement for 2002 Audi A4

its not hard to fix.but you going to have to move some things to get to it. you will need a haynes repair manual.it will show you photos and instructions how to replace it.

Posted on Jul 05, 2009

  • 51 Answers

SOURCE: locating and replacing a camshaft sensor in a 2005 dodge neon

this is a very very simple procedure. you do not need pics. there is a sensor located at the end of the engine on the far side from the belts. at the top. it has a plug with two wires in it. just remove the two 10mm bolts un hook the plug and reverse the process to reinstall. if you have a factory intake you may have to remove it to access this sensor. just the intake tube.

Posted on Aug 08, 2009

steve_e_uk
  • 1675 Answers

SOURCE: BMW X5 CAMSHAFT POSITION SENSOR A .SHOW DIAGRAM

hi i have a diagram if you would like it i could email it to you and there are 2 of them does it say which one it is? you can email me at
s.e.morris@hotmail.co.uk
and i will send you the diagram hope this helps

Posted on Mar 21, 2010

  • 1 Answer

SOURCE: Replace intake camshaft position sensor on 2001 BMW 325ci

http://forums.bimmerforums.com/forum/showthread.php?t=1209580 If you need to replace the intake
This link will guide you thru step by step with pix... it took me approx. an hour to replace!! Good luck!!!!
liz@hunterconstructionpartners.com

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 BMW 745i engine codes P0021,P034,P0393


P0021:"A" Camshaft Position - Timing Over-Advanced or System Performance Bank 2, check timing chain for wear
P0034 :Bypass Valve Control Circuit Low, check crank vent valve.
P0393 :Camshaft position (CMP) sensor B, bank 2 - circuit high input

Jun 24, 2017 | BMW 745i Cars & Trucks

1 Answer

Locate camshaft sensor 2008 3.6l malibu


Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Sep 02, 2016 | 2008 Chevrolet Malibu

2 Answers

06 bmw 525i codes p0174, p0171, p1338, p0340, p0365, and p1315


codes p 0171 and 174 refer ti system too lean
codes p 0338,340,365 refers to crank. and can shaft position sensors
code p1338 again is camshaft position sensor
code p1315 again is camshaft position sensor
too lean can be from fuel pump pressure too low
and position sensors can be wiring , connections sensors.
Involved in all these , one of the possible causes is the ECM
IF it is possible get a serviceable replacement ECM unit and substitute it first as there is no point in replacing all the rest if the ECM is faulty
could be water in the connections , corrosion etc
it is always suspect when so many different codes suddenly appear at the same time

Aug 22, 2016 | BMW Cars & Trucks

2 Answers

Where is the camshaft sensor located on a 2002 infiniti q45 bank 1


This picture here showing the engine from the rear.
26234571-o0t3jm2tua52hbieh0arlv4t-3-0.jpg

Jul 09, 2016 | 2002 Infiniti Q45

1 Answer

I have a 2002 bmw x5.failed deq.error codes p0505(idle control system malfunction)and p0365(camshaft position sensor "B" circuit bank 1) I need to know what the actual problem is concerning these 2...


The 505 is likely the result of the 365. The camshaft position sensor is needed to help determine what idle should be. Most likely the sensor is worn out (oil gets past the seal inside and shorts out the electrical components) and needs to be replaced. Clear codes after replacement before driving.

Dec 04, 2014 | BMW Cars & Trucks

1 Answer

2004 745li po368 code camshaft sensor B-Bank 1 but where is it located?


Intake camsensor bank #1 is located at the back of the right valve cover on the left side above the impulse wheel
Exhaust cam sensor bank #1 is located just to the right of the intake cam sensor no the back of the valve cover
Do you now where # 1 cylinder is that bank one (rule of thumb)

Apr 30, 2011 | BMW 7 Series Cars & Trucks

1 Answer

Bmw 2001 325ci error codes P0019 and P0044


Hi

The codes are P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) &
P0044 HO2S Heater Control Circuit High (Bank 1 Sensor 3)

Regards Dan

Jan 01, 2011 | 2001 BMW 325

3 Answers

Camshaft Poaition Sensor


a picture is worth 1000 words if ya need more help let me know5a5f7cf.jpg684e6e1.jpg

Aug 24, 2008 | 1999 BMW 7 Series

1 Answer

Camshaft Position Sensor


I have a 2000 x5 4.4 my problem is i can turn the ingintion switch wait about 3 to 4 second and the SUV will start. Or sometime I have to turn the inginiton switch all the way off and back on again before it start. I have had the ingintion replaced about 9 months ago.

Jul 23, 2008 | 2005 BMW X5

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...