Question about Cars & Trucks
Here's a link on how to replace.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528006be73 Here's the part.http://www.autozone.com/autozone/parts/1992-Ford-Thunderbird/Master-Cylinder-Brake-System/_/N-ix2fyZ8kn47 the hydralic unit is different and expensive,see.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528006becd here's the part,wow.http://www.autozone.com/autozone/parts/1992-Ford-Thunderbird/ABS-Hydraulic-Unit/_/N-ix2fyZ8kobu
Posted on Oct 29, 2012
When you see anti lock and brakes warning lights your braking system failing.your hydralic unit electric motor could be failing not building enough pressure to work the mastercylinder.
Posted on Oct 30, 2012
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Anti-lock brake light stays on
My wife took the car to exaust pro in Lexington, Ky. They did a scan and it was a speed sensor. They replaced it and it is fine. The car is great but after hearing all the complaints about the heater core we are going to sell it and get a Toyota Avalon. Also I replaced the antenna mast at 35k.
Posted on Jul 31, 2008
Adjust your rear brake shoes. Then rebleed the system. Start at the master cylinder Bleed master first then the wheel furthest away from the master (right rear then left rear then right front then left front. Do that and your pedal should be good.
Posted on Dec 30, 2008
SOURCE: anti lock brake system
If the light is not on it may not be the ABS that is pulsating on slow braking but it may be that your have warped brake rotors, even if the rotors were replaced with the pads the new ones may be warped already, we always check new rotors on a brake lathe before installing them because we have seen this happen many times
Posted on Feb 02, 2009
Did your mechanic use a DRB III or equivalent scanner before performing the bleeding procedure after installing the master cylinder? This is a requirement by the manufacturer (Chrysler) when bleeding the brake system.
Posted on May 15, 2009
One of the sensors has gone bad and needs to be replaced, the other thing to that would also do that is the ABS sensor is dirty or needs to be re gaped to the speed ring on the hub. There was a issue bulletin with your Tahoe on the ABS activating under 8 km/h. Good luck and hope this helps, if not clean out the sensor with brake parts cleaner and check the wire harness and ABS sensor bracket. Re gap the sensor to the speed ring hub. Here is the bulletin. Anti lock Brake (ABS) Activation at Low Speeds (Clean Wheel Speed Sensor Mounting Surface) #03-05-25-007C - (05/16/2006) 2001-2006 Chevrolet Suburban, Tahoe
Posted on Jun 05, 2009
Tips for a great answer:
Sep 03, 2014 | 2001 Ford Taurus
Jan 21, 2013 | 1994 Isuzu Pickup
Nov 20, 2010 | Mercedes-Benz 560-Series Cars & Trucks
May 25, 2010 | 2002 Buick Century
Feb 12, 2010 | 1992 Ford Thunderbird
Oct 10, 2009 | 1992 Ford Thunderbird
Oct 09, 2009 | 1992 Cadillac Fleetwood
Aug 24, 2009 | 1992 Ford Thunderbird
May 26, 2018 | Cars & Trucks
149 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: