Question about 2001 Volvo S80

Open Question

Fault ecm 0039

Volvo s80 2.5 td very slow when setting of had it on computer its come up with fault ecm0039 what is this

Posted by on

6 Suggested Answers

  • 1 Answer

SOURCE: volvo s80 dashboard fault

I recently purchased a 2002 S60 D5 which had this problem. I am not a Volvo expert so don't know if it could be the same fault, but it sounds identical. No lights, gauges etc, but intermittently and very briefly comes on. Having heard some silly prices for replacement dash and ECU, I had a look. I found 4 poor soldered joints on the dash circuit board (top left processor & heat sink). I cleaned them and re-soldered them, although I had continuity just after cleaning the corrosion. The dashboard has worked perfectly since (3 weeks) . If you try this make sure you disconnect the battery first or you may have the SRS airbag warning light on! (I had to have it re-set at the dealers!!)

The whole process took less than an hour. If you are not electronically savvi get one of your mates who is to have a look..

Posted on Apr 21, 2009

  • 5 Answers

SOURCE: I have a 2000 volvo s80 t6 and have fault codes

I think that you have a contaminated or bad Mass Air Flow (MAF) sensor. It's located by the engine air filter housing. You can get a used one online for less then 100.

Posted on Aug 11, 2009

  • 13 Answers

SOURCE: volvo s80 dashboard fault

This is a known problem although Volvo will not admit it. The dash needs to come out (10 min job) and sent away for a simple repair. Total cost is about £150 but you will need to get the SRS warning that will be showing in the LED message display cancelled by a Volvo dealer after the dash has come back. Don't try a scrapyard dashboard the ECUs have IP addresses. I used a company in Kent to do the repair. Get onto Google there may be a repairer more local.

Posted on May 09, 2010

  • 738 Answers

SOURCE: 2007 Volvo XC90 fault codes-ECM P030000, P030100,

first code means random/multiple misfire cylinder (s) detected
second code means misfire detected number 1 cylinder, third code, miss=fire number 3 cylinder fourth code misfire number 4 cylinder
causes can be spark plugs, HT leads, ignition coils, injector, wiring fault, low compression/ engine mechanical fault

Posted on Jun 04, 2010

  • 1 Answer

SOURCE: how to reset service message on volvo s80?

2002-2007 All Volvo Models

  • The service reminder indicator lamp illuminates for 120 seconds when the ignition is first switched on
  • Insert key and turn Ignition Switch to position I
  • Press and hold in the reset button for the trip odometer
  • Turn the Ignition switch to position II (within 2 seconds)
  • Hold the reset button for the trip meter pressed in until the original trip counter value blinks and is redisplayed
    (For all vehicles 2003- a general yellow lamp will light when the reset button must be released.)
  • Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
  • If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.
  • If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.

Posted on Aug 22, 2010

ZJLimited
  • 17970 Answers

SOURCE: what causes the following faults code on 2004 volvo S40 :ECM-250A LONG TERM-FUEL TRIM:UPPER LIMIT,BCM-0100 COMMUNICATION PROBLEM WITH ECM,EPS-0082 ENGINE STATUS FAULTY SIGNAL,CCM-001 COMMUNICATION CON

Check, test or replace MAF sensor.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Jul 09, 2012

Testimonial: "my volvo "check engine light"problem solved after replacing MAF sensor. thanx to FixYa!!!!!!!!! "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi im Have Volvo S40 2.0Diesel the computer show ECM-2683 Bypass valve signal too high.Whats part I need to replace?


The engine control module (ECM) checks the signal from the by-pass valve in the thermostat housing. The diagnostic trouble code (DTC) is stored if the signal from the by-pass valve is too high. The fault is diagnosed by the engine control module (ECM) when the ignition is on.
Check for short-circuit to supply voltage in the signal cable.

Mar 17, 2015 | Volvo S40 Cars & Trucks

1 Answer

Volvo s40 2001. ecm 62


cam timing fault, either engine is sludged, timing is off or you have a faulty cam timing pulley, These pulleys can leak engine oil in timing cover and due to bleed down the fault 62 can be set, If you see engine oil in timing cover you may need a t-belt job, actuator pulley and while doing this, a flame trap service,

Sep 11, 2013 | Cars & Trucks

1 Answer

2000 radiator fan test, is there any way to test the fan before o get a new one


check cooling fan fuse or fuse link.it all is good. fan relay or engine coolant temperature sensor.could have ECM FAULT it controls coolant fan relay and coolant fan.code scan for ECM FAULT YOU WILL SEE CHECK ENGINE FLASH IF PROBLEM IN THE ECM.but check cooling fan hot wire it using jumper wires to battery.if fan okay replace engine coolant temperature sensor.

Feb 20, 2013 | 1999 Volvo S80

1 Answer

I have a code p1652 for my volvo 2004 xc90 can someone tell me is this a computer problem


P1652 or ECM982A: Manufacturer controlled computer output circuit, Engine control module (ECM) internal fault. (Permanent fault, can't clear without a code reset)

Nov 22, 2012 | Cars & Trucks

1 Answer

What causes the following faults code on 2004 volvo S40 :ECM-250A LONG TERM-FUEL TRIM:UPPER LIMIT,BCM-0100 COMMUNICATION PROBLEM WITH ECM,EPS-0082 ENGINE STATUS FAULTY SIGNAL,CCM-001 COMMUNICATION CONTROL...


Check, test or replace MAF sensor.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 09, 2012 | 2004 Volvo S40

1 Answer

Thier shoud be a recall volvo with p1618


CODE P1618 - CABLE FAULT BETWEEN AW 50 Q2 TRANSMISSION CONTROL MODULE AND MOTRONIC 4.4 ENGINE CONTROL MODULE. YOU CAN CHECK FOR RECALLS BUT I DONT THINK THERE IS RECALL FOR YOUR PROBLEM. YOUR PROBLEM IN TRANSMISSION CABLE COULD BE LOOSE OUT OF PLACE DAMAGED OR YOU HAVE TCM ECM FAULT.

Aug 15, 2011 | 2001 Volvo S80

1 Answer

2007 Volvo XC90 fault codes-ECM P030000, P030100, P030300, P0304000, what do they mean?


first code means random/multiple misfire cylinder (s) detected
second code means misfire detected number 1 cylinder, third code, miss=fire number 3 cylinder fourth code misfire number 4 cylinder
causes can be spark plugs, HT leads, ignition coils, injector, wiring fault, low compression/ engine mechanical fault

Jun 04, 2010 | 2007 Volvo XC90 V8 AWD Sport

1 Answer

I have the same probleme p0171 what else can be? the rpm goes up and down sometimes.


ECM Software If there are no faults found, there is a Volvo tech note regarding upgrading the Engine Control Module (ECM) software for this code.

Nov 05, 2009 | 2004 Volvo S60

Not finding what you are looking for?
2001 Volvo S80 Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...