Question about 2005 Ford Ranger

1 Answer

Tail light Assembly - How to install.

Ford Ranger XLT year 2005
How do you install a passenger's side tail light assembly.
I have bought a replacement since my lens is cracked
Can anyone help me please

e-mail: gina-tc@comcast.net

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The ford ranger bulb housing is pretty weird and hard but you have to turd the bulb and housing all the way to one direction then press agianst the back of the tail light with the bulb and housing in and slowly turn and it should eventually work for you,it took me a while, its one of those things that you spend hours on and then it randomly decideds to work.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the full light bulb on a ford Galaxy ghia


Hmmm Learn something new every day. Didn't know Ford had resurrected the Galaxy line, let alone put it on a van. Oh well. If Ford were kind, you should be able to access the back of the tail light assembly from the inside. There should be access panels, one behind each tail light assembly. Your owners manual should have the information. If not, a Chiltons/Haynes repair manual that covers the make/model/year will certainly lead you through the procedure.

Nov 27, 2014 | 2005 Ford Galaxy 2.3

1 Answer

How do I replace 2004 Pontiac Vibe passenger side tail light assembly?


Hello Tim.

Here is the procedure.
  1. Open the rear compartment lid.
  2. Remove the rear compartment trim panel (4).
  3. Remove the tail lamp socket (2) from the tail lamp(7).
  4. Remove the tail lampbulb (1) from the lamp socket (2).
kiltylake_125.gif


There you are, Happy New year.

KL

Jan 01, 2011 | 2004 Pontiac Vibe

1 Answer

Need diagram, showing which fuse needed on Ford Ranger XLT 1988


REPLACE THE BULBS BECAUSE THE BULBS HAVE 2 ELEMENTS IN SIDE THEM ONE ELEMENT CONTROLS THE BRAKE LIGHTS THE OTHER DOES THE TAIL LIGHTS

May 13, 2010 | 1988 Ford Ranger

2 Answers

Instructions,repairing a rear passenger tail light assembly for 2004 Hyundai Santa Fe


Made a video of me replacing the brake light but I show how to remove and install the tail light assembly. It's on a 2005 Hyundai Santa Fe but should be the same as a 2004.

Dec 18, 2009 | 2003 Hyundai Santa Fe

1 Answer

2004 Ranger: Left tail assembly assembly will not


perhaps its the wrong bulb or the bulb isn't incerted correctly, had this problem on my moms truck.

Aug 21, 2009 | 2004 Ford Ranger

1 Answer

How do you change tail lights for the 2003 passat


Rear Turn Signal, Brake and Parking Lights Removal & Installation To Remove
  1. Remove or disconnect the following:
    • Harness connector
    • Combination nuts
    • Lamp and its assembly toward rear
To Install:
  1. Install or connect the following:
    • Lamp and its assembly into position
    • Combination nuts; torque to 35 lb-in. (4 Nm)
    • Harness connector
This is the only thing the tech manual says.

Jul 22, 2009 | 2003 Volkswagen Passat

1 Answer

How to access tail light bulb in 2005 ford f-150


Drop the tailgate, on the inside of bed where tailgate closes are couple of screws.These hold the light assembly in the bed. remove the screws, then remove light assembly. The light bulb can be removed from back of the tail light assembly. Check to make sure the lightbulb work before you put the tail light back together. Good luck and hope this helps and don't forget to add some grease to the light socket to prevent corrosion. 

Jun 24, 2009 | 2005 Ford F-150

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

Replacing rear turn signal bulb in 2003 Mustang


remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

Dec 04, 2008 | 2003 Ford Mustang

1 Answer

Replacing tail light assembly


you will need to open the trunk remove the trunk cover and it is normally a 10mm socket and then all you do is unplug the wires and put the new one in the same way you took the old one off

Oct 10, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
2005 Ford Ranger Logo

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...