Do it right the first time
Anonymous posted an answer for this Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum:
"Hope this helps"
Anonymous posted an answer for this Kenmore 22812 Bagged Canister Vacuum:
"You may not have power to the power head. Check the plug at the neck of the power head,..."
Anonymous posted an answer for this Bissell 1692 PowerSteamer Upright Vacuum:
"If the cogs on the belt and brush roll are ok, then probably the cogs on the pulley are..."
Anonymous posted an answer for this Dyson DC07 Animal Bagless Upright Cyclonic Vacuum:
"Sorry I really can't give you an honest answer. I don't care for the Dyson vacuum and..."
Anonymous posted an answer for this Riccar 8850 Vacuum:
"On the belt end, there is a clip #59 to remove then you can take the brush roll apart,..."
Anonymous posted an answer for this Kenmore 23313 Whispertone Bagged Canister Vacuum:
"Sounds like you may have a bad or loose connection, could be one of wires in the hose to..."
Anonymous posted an answer for this Kenmore 85920 PowerSpin Upright Wet/Dry Vacuum:
"If it is available, go to Sears.com, click on the parts link, put in your complete model..."
Anonymous posted an answer for this Kenmore 85920 PowerSpin Upright Wet/Dry Vacuum:
"If the recovery tank lid has a foam filter make sure that it has at least a 1/4 inch gap..."
Anonymous posted an answer for this Kenmore 85920 PowerSpin Upright Wet/Dry Vacuum:
"Find the model number, then go to sears.com, click on parts and put in your complete model..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"You will have to replace the switch, Takeout the 4 screws on the back of the handle, it..."
Anonymous posted an answer for this Beam Industries Wet/Dry Auto Central System Vacuum:
"Set the bottom part of the handle down(not the part that the screws go in)the contact..."
Anonymous posted an answer for this Hoover Vacuums:
"Should be a clamp on each end to undo, then the hose will come off."
Anonymous posted an answer for this Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum:
"I assume you mean the vacuum motor isn't running, could be the switch, cord or the motor,..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"The thermo is a small square piece with two wires coming out of it. Did you check the..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"There should be a belt tensioner for the V belt, maybe it is not contacting the belt when..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"There is a belt tensioner that maybe not contacting the belt when you tilt the handle..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"You either have a problem with the sensor or the circuit board. Most times it is with the..."
Anonymous posted an answer for this Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum:
"Take the handle off, then remove the tool holder, then you can get to the switch. Just has..."
Anonymous posted an answer for this Kirby G4 Bagged Upright Vacuum:
"Sounds like something is not in the right place. Tghere are safety switches, one on the..."
Anonymous posted an answer for this Eureka 4700A Maxima Bagless Upright Vacuum:
"If it went dead, and restarted after it cooled off, then check for a clog in the hose or..."
Anonymous posted an answer for this Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum:
"Make sure all filters are clean, also check the inlet by the brush roll isn't clogged as..."
Anonymous posted an answer for this Kenmore Vacuums:
"You could have a bad switch in the handle on the hose, may also be that the female plug at..."
Anonymous posted an answer for this Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum:
"You need to replace the brush roll, part # 2032013, I would also put a new belt on as..."
Anonymous posted an answer for this Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum:
"That is the problem with a bagless, but if you keep the filters clean it won't be quite as..."
Anonymous posted an answer for this Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum:
"The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun..."
Anonymous posted an answer for this Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum:
"Your motor is must likely bad and you would look at around $60 to $70 for a new one."
Anonymous posted an answer for this Bissell Vacuums:
"Hopefully this solution is for the model you have: Does water squirt out of the hose..."