Anonymous posted an answer for this Singer Quantum XL-1000 Computerized Sewing Machine:
"When I plug the embroidery component into the machine the foot pedal doesn't work on the..."
Anonymous posted an answer for this Singer Quantum XL-1000 Computerized Sewing Machine:
"When the embroidery unit is on the foot pedal is not needed. So just remove it."
Anonymous posted an answer for this Bernina Sewing Machines:
"It looks like your timing of your bobbin hook is out you will need to have a service man..."
Anonymous posted an answer for this Sewing Machines:
"the needle bent during sewing and since i put the new one in,the main thread is not..."
Anonymous posted an answer for this Bernina Artista 180:
"If you have the machine connected to the computer you can delete the embroidery from your..."
Anonymous posted an answer for this Bernina Sewing Machines:
"Turn the small screw on the bobbin holder.clockwise to tighten and anti clockwise to..."
Anonymous posted an answer for this Sewing Machines:
"need to adjust bobbin tension"
Anonymous posted an answer for this Bernina Artista 180:
"I have three artista design cards for this machine. That I need to sell $50 each...."
Anonymous posted an answer for this Bernina Artista 180:
"I am looking for the embroidery cards that fit into the embrodery arm for the Bernina..."
Anonymous posted an answer for this Janome Memory Craft 9000 Computerized Sewing Machine:
"You may have a broken belt, or your feed dogs are down."
Anonymous posted an answer for this Janome Memory Craft 9000 Computerized Sewing Machine:
"All Janome machines need either easy transfer software or customizer software to transfer..."
Anonymous posted an answer for this Janome Memory Craft 10000:
"Open your customizer software cd and look for the drivers, you will have two drivers on..."
Anonymous posted an answer for this Janome Memory Craft 10000:
"Your timing is out and will have to be put in to have it adjusted."
Anonymous posted an answer for this Janome Memory Craft 10000:
"See if you can run the program in compatibility mode, with win 2000 or xp."
Anonymous posted an answer for this Janome Memory Craft 10000:
"lower your top tension down, as it is tighter then your bobbin thread and also tighten..."
Anonymous posted an answer for this Janome Memory Craft 10000:
"If you have the customiser software open the disk up to view the drivers the driver may..."
Anonymous posted an answer for this Brother XR7700:
"Drop the bobbin with the elastic in the holder without feeding it through the holder, and..."
Anonymous posted an answer for this Brother CS6000i Computerized Sewing Machine:
"Have you got the bobbin in the correct way around, also have you put the needle in correct..."
Anonymous posted an answer for this Brother LS-2125 Mechanical Sewing Machine:
"Make sure that your needle is put in the correct way, there is a groove in the front of..."
Anonymous posted an answer for this Brother LS-2125 Mechanical Sewing Machine:
"most of the newer machines have a drop in bobbin that the bobbin turns anti clockwise if..."
Anonymous posted an answer for this Brother LS-2125 Mechanical Sewing Machine:
"but is the carriage moving,? if not disconnect and try to connect again, the embroidery..."
Anonymous posted an answer for this Bernina Bernette Deco 600:
"Your feed dogs sound like they are getting stuck,chec whether they are on the down..."
Anonymous posted an answer for this Bernina Bernette Deco 600:
"If your deco wizard is the same as the pe-design 2,3,4 you can transfer your designs to..."
Anonymous posted an answer for this Bernina Bernette Deco 600:
"Your timing is out in the bobbin area this will have to be reset, maybe the last time that..."
Anonymous posted an answer for this Bernina Bernette Deco 600:
"Maybe you are transferring too larger design over to the machine try a small design and..."