2
Tim Venetis posted an answer for this Garden:
"Briggs told me the torque is 220 inch pounds"
Tim VenetisTim Venetis posted a question about John Deere Garden:
"John Deere lt155 deck beltt Problem"
Tim Venetis
Tim Venetis posted an answer for this Refrigerators:
"Sometimes the timer jmalfunctions and the refrigerator will not go in to a defrost mode...."
Tim Venetis
Tim Venetis posted an answer for this Dyson Vacuums:
"Make sure there is nothing lodged in the roller and check the belt that turns the roller..."
Tim Venetis
Tim Venetis posted an answer for this Honda Electrical Supplies:
"SSounds like either you have a hole in the muffler or the muffler bolts loosened up."
Tim VenetisTim Venetis posted an answer for this Garden:
"Make sure you have the brake mechanism that holds the sprocked released by pulling the..."
Tim Venetis
Tim Venetis posted an answer for this Washing Machines:
"SSounds like the timer mechanism is not switching off the motor of the washing machine."
Tim Venetis
Tim Venetis posted an answer for this Sentry Home Security:
"SSounds like the mechanism is rusty. Spray some wd40 oon the rod and levers that go in the..."
Tim VenetisTim Venetis posted an answer for this Dirt Devil Vacuums:
"Take the hose off where it goes in to the vacuum and see if there is something lodged in..."
Tim Venetis
Tim Venetis posted an answer for this Buick Cars & Trucks:
"Check the wiring harness to the fan they sometimes put a fuseable link in the wire and it..."
Tim Venetis
Tim Venetis posted an answer for this Panasonic Audio Players & Recorders:
"It sounds like you have a bad tape or the 8 track head has to be adjusted."
Tim Venetis
Tim Venetis posted an answer for this Briggs Stratton H7159 & Stratton® 5500, 10 HP Generator:
"it sounds that the gasket was not put on properly and the engine leaked all the oil out of..."
Tim Venetis
Tim Venetis posted an answer for this Briggs Stratton 7,000 Watt Automatic Home Standby System with 50 amp :
"There is air in the line and some times thaey have a primer button on the line near the..."
Tim VenetisTim Venetis posted an answer for this Briggs Stratton H7159 & Stratton® 5500, 10 HP Generator:
"You have to unbolt the rubber wheel that goes against the metal disc first."
Tim Venetis
Tim Venetis posted an answer for this Briggs Stratton Portable Generator 305cc Engine 8250 Surge Watts 5500 Running Watts Model 030439:
"You have to go to a lawnmower repair shop with your model code and type of your engine on..."
Tim VenetisTim Venetis posted an answer for this Briggs Stratton H7159 & Stratton® 5500, 10 HP Generator:
"Sounds like you have remove and disassemble the carburetor and clean it."
Tim VenetisTim Venetis posted an answer for this Briggs Stratton H7159 & Stratton® 5500, 10 HP Generator:
"You have unloosen the bolt slightly that holds the armature to the engine and since they..."
Tim Venetis
Tim Venetis posted an answer for this Briggs & Stratton 20-Amp Extenda Panel - 1659:
"Remove the recoil shroud and make sure that there is no mouse nest around the coil area..."
Tim VenetisTim Venetis posted an answer for this Briggs Stratton Portable Generator 305cc Engine 8250 Surge Watts 5500 Running Watts Model 030439:
"Take a spray of carb cleaner and clean the linkage mechanism from the governor to the..."
Tim Venetis
Tim Venetis posted an answer for this Briggs & Stratton Snowblower Snow Blower Tiller Generator Gas Fuel Tank 799863:
"Remove the nut that holds the float bowl on and clean the hole on the side and the hole..."
Tim VenetisTim Venetis posted an answer for this Briggs & Stratton Snowblower Snow Blower Tiller Generator Gas Fuel Tank 799863:
"Sometimes on them the throttle shaft which goes in to the carburetor gets rusty and turns..."
Tim VenetisTim Venetis posted an answer for this Briggs & Stratton Snowblower Snow Blower Tiller Generator Gas Fuel Tank 799863:
"Make sure fuel is getting to the carburetor if it is take the carb apart and check that..."
Tim Venetis
Tim Venetis posted an answer for this Briggs and Stratton 073001 2" Portable Gas Powered 5.5 HP Water Pump:
"Take the float bowl off and replace the float needle and seat after you make sure every..."
Tim VenetisTim Venetis posted an answer for this Briggs Stratton H7159 & Stratton® 5500, 10 HP Generator:
"The gap is .010. You can also use a card to gap the coil and after you tighten the coil..."
Tim Venetis
Tim Venetis posted an answer for this Briggs & Stratton Lawnmower Quantum Starter Cup 791960:
"After you remove the nut that holds the cup on the key way is under the cup and the..."
Tim Venetis
Tim Venetis posted an answer for this Briggs & Stratton Governor Spring 691817 Od:
"First make sure the throttle lever is on full speed position then unloosen the bolt that..."
Tim VenetisTim Venetis posted an answer for this Briggs & Stratton Snowblower Snow Blower Tiller Generator Gas Fuel Tank 799863:
"Look for the spark plug wire which usually comes out from the recoil shoud and follow it ..."
Tim VenetisTim Venetis posted an answer for this Briggs Electrical Supplies:
"Take the bowl off the carb and make sure the float allows fuel to fill the bowl when the..."
Tim VenetisTim Venetis posted an answer for this Garden:
"Make sure the battery is putting out 12 volts by measuring it with a volt meter."
Tim VenetisTim Venetis posted an answer for this Craftsman Garden:
"If you take the recoil housing off you probably will find a mouse nest by the flywheel and..."
Tim VenetisTim Venetis posted an answer for this Garden:
"Check to see you are getting spark at the spark plug. Take the plug out and put the plug..."
Tim Venetis
Garden 93 answers
Electrical Supplies 42 answers
Vacuums 40 answers
Heating & Cooling 21 answers
Air Tools & Compressors 12 answers
Saws 11 answers
Drills 9 answers
Measuring Tools & Sensors 5 answers
Dehumidifiers 5 answers
Tools & Hardware - Others 4 answers
