1Mr Fixit
Joe Grech posted an answer for this Singer Inspiration 4210 Mechanical Sewing Machine:
"Hi you will have to go through your timing and needle bar adjustment's also could have..."
Joe Grech
Joe Grech posted an answer for this Singer Sewing Machines:
"Hi check your hook to needle clearance and timing, could also be a burr on the hook or..."
Joe GrechJoe Grech posted an answer for this Singer Sewing Machines:
"The leather belt has a steel U shaped clip that is pushed through a small hole in each end..."
Joe GrechJoe Grech posted an answer for this Singer Sewing Machines:
"Hi the point of the hook should be in line with the needle and just above the hole in the..."
Joe GrechJoe Grech posted an answer for this Singer Sewing Machines:
"Hi the spool holder on this machine is just a plastic rod with a slight taper and it just..."
Joe Grech
Joe Grech posted an answer for this Brother CS6000i Computerized Sewing Machine:
"Hi if the needle is hitting the needle plate you best get in touch with who you bought it..."
Joe GrechJoe Grech posted an answer for this Singer Sewing Machines:
"Hi either the bobbin is not locking onto the spindle or the rubber wheel inside has not..."
Joe GrechJoe Grech posted an answer for this Sewing Machines:
"Hi Loops on the back is usually the top tension adjustment too loose, make sure machine is..."
Joe Grech
Joe Grech posted an answer for this 1983 Holden VH Commodore:
"Hi Could be worn brushes on slip ring or faulty diode on the rectifier. Check all the..."
Joe Grech
Joe Grech posted an answer for this 2003 Suzuki Grand Vitara:
"Sorry in the tank"
Joe Grech
Joe Grech posted an answer for this Morris Cars & Trucks:
"Hi you have to remove the gearbox to remove the slave cylinder. You can replace the seal..."
Joe GrechJoe Grech posted an answer for this Morris Cars & Trucks:
"Hi sounds like you have a bad earth issue or faulty or wrong coil Morris usually run a..."
Joe GrechJoe Grech posted an answer for this Morris Cars & Trucks:
"Hi sounds like a steering tie rod is worn plus an out of balance wheel get a wheel..."
Joe Grech
Joe Grech posted an answer for this 1969 Morris Minor:
"Hi The distributer should have an offset drive so it can only go back in the same way it..."
Joe Grech
Joe Grech posted an answer for this 1955 Morris Minor:
"Hi bit tricky but not hard you have to remove the dash panels to access the spindle mounts..."
Joe GrechJoe Grech posted an answer for this Morris Cars & Trucks:
"Hi, I work on a lot of vintage cars and NOT 100% sure what factory specs are but have..."
Joe Grech
Joe Grech posted an answer for this 2002 Cadillac Seville:
"Hi Alex, 1 = ON A SAFTY ISSUE NEVER OPEN THE PRESSURE CAP ON ANY SYSTEM WHEN ENGINE IS..."
Joe GrechJoe Grech posted an answer for this Brother Sewing Machines:
"Hi if the main shaft is turning the fault is a faulty encoder if it is not turning faulty..."
Joe Grech
Joe Grech posted an answer for this Yamata FY900 Mechanical Sewing Machine:
"Hi usually when an auto threader jams in the out position the problem is the small hook..."
Joe Grech
Joe Grech posted an answer for this Refrigerators:
"Hi English gun makers would often supply samples with cut outs for training as these were..."
Joe Grech
Joe Grech posted an answer for this HOT TOYS 16 Modern Firearms 3 Akm W Drum:
"Hi the number you list doesn't seem to be right "T" designates a 22L/R the 80 seems to be..."
Joe Grech
Joe Grech posted an answer for this White Sewing Speedylock 1600 Mechanical Sewing Machine:
"The thread can strip either on the the screw or the bar it goes into, usually it is just..."
Joe GrechJoe Grech posted an answer for this Husqvarna Daisy 310:
"Souds like a stitch balance problem how long since the machine was serviced as the..."
Joe Grech
Sewing Machines 14 answers
Cars & Trucks 9 answers
Toys 1 answer
Refrigerators 1 answer
