Zapco Car Audio & Video - Answered Questions & Fixed Issues
I installed a 400 watt zapco competition amp\
are you sure you didnt wire the amplifier the front and rear to left/ right?check your deck settings to see that the rear speaker rca are connected.check all wires are connected.push the mono or bridge buttons are off.provide more info.
11/15/2013 4:48:22 AM •
Zapco I-450...
•
Answered
on Nov 15, 2013
•
86 views
Install my amp
Go to this link and see page 47http://www.zapco.com/files/Download/DCRef.pdf
How many rms does my
4-channel, 4 ohms: 4 x 50 Watts
4-channel, 2 ohms: 4 x 90Watts
Stereo, 4 ohms: 2 x 180 Watts
T.H.D. : Frequency Response: 10 - 25KHz
S/N Ratio: >90dB
Channel Separation: >50dB
Dimensions: 13"L x 9.9"W x 2.25"H
Zapco I450 Zapco I 450 iForce Series 4 Ch. 360 Watt Amplifier
5/23/2011 8:38:50 AM •
Zapco I-450...
•
Answered
on May 23, 2011
•
253 views
I need a manual for
i got a wiring paper that comes with the peq plug,its not a manual but it shows how to wire up a zapco peq
I have a zapco refrence 750.2 has no sound output
check your settings on your stereo and the amp make sure you have changed to 1 ohm on the amlifier for a briged connection to a subwoofer and change from lpf to hpf on the amp there should be a switch.
...storing noise detected from my
Storing as in Distortion? If that's the case lower the output gain from your amp until it is suitable to you ears. It might be all the way open, besides this should be adjusted system to system.
Sparks up with power wires no turn on
If your car battery was not disconnected when the amp was installed them your amp has blown, it could just be a fuse or at worst the circuits inside have fried. Check your fuses if not take it to a certified car audio shop and ask them to have a look at it for you. Need more information to help you bruv, but from what you have said it has been connected with the car battery still connected
Bass only going to rear speakers. How do I get
Hello michaelandta,
Check your filter settings on the front channels. It sounds like they may be set to "high pass" which would eliminate the bass frequencies. If you are using the amp to power normal speakers, it's usually best to set the filters for "full range". If the amp only has "low pass" and "high pass" settings, turn them both OFF.
Hope this helps.
9/12/2009 3:57:58 AM •
Zapco I-450...
•
Answered
on Sep 12, 2009
•
150 views
What is the left and right clip light?
the left and right clips are for your subs to tell your amp that they are not going to (flatline) clip which is when you start to lose clarity and get distortion
Zapco ag 350
Check your ground and make sure it is properly grounded ....it needs to be a very clean paint/gum free area tightly bolted. Next Check and make sure you are recieving your 12 volts (not running) 13 (running) by placing your test leads from positive to ground...... then make sure your power remote from your head unit is putting out voltage.
ZAPCO 9.0
Go here first http://www.zapco.com/ Good Luck
Help with code radio for my nissan pp2787h
The radio code is a security feature that's meant to deter theft, and it's unique to each vehicle. If you've lost your code, you'll need to contact a Nissan dealership or service center and provide proof of ownership. They should be able to help you retrieve the code. Please do not attempt to use codes from the internet as incorrect attempts may lock your radio.
4/18/2024 1:48:21 PM •
Car Audio &...
•
Answered
on Apr 18, 2024
•
16 views
Is there bluetooth on nsdn-w59
I have the same radio now with no Bluetooth am trying to get Bluetooth on it too without having to buy another radio. Please help.
3/26/2024 3:40:48 AM •
Car Audio &...
•
Answered
on Mar 26, 2024
•
774 views
Not finding what you are looking for?