Zanussi Dryers - Recent Questions, Troubleshooting & Support

Clean the air intake grill t the rear left corner. https://www.manualslib.com/manual/198228/Zanussi-Zdc46130s.html?page=15#manual

Dry bearing and a slipping belt is the most likely reasons. A belt slipping causes vibration and squealing.

Error code 66 on a Zanussi washing machine is a fault code indicating a problem with the control board. The issue could be related to the wiring, the control board itself, or a component connected to the board, such as the heater element. Since you have tested the heater element and found that it appears to be working correctly, it's likely that the issue is with the control board. However, it's always a good idea to double-check all the wiring and connections before replacing any parts. If the problem persists after checking the wiring and connections, it may be necessary to replace the control board. Replacing the control board can be an expensive repair, so it's important to consider the cost of the repair compared to the value of the machine. If the machine is old and the cost of the repair would be more than the value of the machine, it may be more cost-effective to purchase a new machine.

RTM it tells that or google it, sure does. all dryers on earth have spec and a manual and both tell that. by country too.

can be either or something else need to test using a multi meter

I have a galanz airconditioner and is showing an error be there is someone knows what does it means? Thanks

https://www.youtube.com/watch?v=2s5NnqtJGSc

Check the heater. Does it heat?

try out this youtube and see if it works for you? https://www.youtube.com/watch?v=7RzXRKa5ruQ

Hi angela trent
ALWAYS UNPLUG YOUR DRYER BEFORE ATTEMPTING TO DO ANY WORK ON IT.
Check to make sure you are getting full 220 Volt power to the dryer, if you are then:
Check your Wiring
Often the main wiring connection from the house, at the dryer, burns and the connection breaks. If this has happened to your dryer, you need to replace the power cord and the terminal block inside the dryer to which the wire is attached.
Check the Door Switch
If the door switch or the door-switch actuator is defective, the dryer won't work and you need to replace the failed component. The switch is inside the dryer main housing near the door frame. Sometimes you need to raise or open the top or front of the dryer to reach the switch. Check for continuity you should have none with door open, and should have a reading when closed. If not replace the door switch.
Check to make sure you heating problem is not a lint build up in the discharge hose or the dryer,as this condition can cause heater/thermistor problems such as overheating of the heating coil leading to failure of the coil and burnout of the thermostat/thermistor due to overheat.
Remove the back/or front just under the door of the machine and try to locate the air duct going from the blower to the drum. Normally inside/outside the air duct you will find the heating coil and the thermostats/thermistors. Once you have located the heating coil, remove the two wires from it and check the coil with an ohm meter across the two terminals of the coil.
You should read continuity across the terminals, if not you will need to replace the coil as it is faulty.
If the heating coil is ok, then:
You can check the thermostat/thermistor one at a time by removing the two wires and taping them together with electrical tape.
If you have an ohm meter then you can test the thermostat/thermistor/thermal fuse,
then you do not have to tape the wires together as described above.
If the coil heats up then replace the thermostat/thermistor/thermal fuse as it is faulty.
DO NOT LEAVE THE WIRES TAPED TOGETHER AFTER THE TEST AS THIS COULD CAUSE A FIRE BECAUSE YOU HAVE REMOVED THE SAFETY.

If the thermal fuse overheats the dryer will not operate. It's located on the blower housing. It cannot be reset. A vent clogged with lint can cause it to overheat. You can test it with an Ohm meter or continuity checker, if no continuity, replace it)
Right after replacing a dryer element, always run the dryer on 'air fluff' / 'no heat', and go outside to verify there's plenty of air coming out your vent system.
If the vent's clogged, that new element can burn out very quickly.
For video and pictures on how to replace the element go to the following website:
davesrepair.com/DIYhelp/DIYreplacingWPLdryels.htm
This is a FREE answer, Please take time to rate me

Have someone take Dryer apart and clean lint out of cabinet. Sounds like it’s trying to catch fire.

Check the idler pulley. Maybe it was installed incorrectly. Not aware of any adjustment capabilities of a dryer belt.

check door micro switch cheers

I'd suggest - remove the top cover. Switch on. Push the drum around - see if the drum picks up speed and continues to run. If this happens, it means that the motor Starter capacitor has gone dud and will need replacing. Note- If the drum doesn't continue to rotate after you shove it, switch off immediately. It will likely then be a faulty motor.

I think you should read the instruction manual . 3 beeps means some information to begin a solutin.

your on the right ytack and they are normally easy to replace