Zanussi Logo

Zanussi Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 284 Products
  • 6K Answers

Before it will start the brain needs to know the door is closed and locked. The door catch is connected to the brain - perhaps they are no longer communicating...

Zanussi Washing... | Answered on Jun 24, 2020

If the START / PAUSE button lights up red, the washing machine detects a malfunction. Now you should count how many times the START / PAUSE button lights up red and tell to us what kind of malfunction is being done.

Try to rapid reading of alarm codes when the appliance is in normal operating mode (e.g. during the execution of the washing
Press and hold down START/PAUSE and the nearest option button for at least two seconds: the LEDs initially switch off, and then display the flashing sequence indicating the last alarm.

LED indicator START / PAUSE with red light = indicates the first digit of the alarm code (family)
• LED indicator START / PAUSE with green light = indicates the second digit of the alarm code (internal number of the family)


Zanussi Washing... | Answered on May 25, 2020

Zanussi Washing... | Answered on May 23, 2020

Is this the first time it's happened? Normally, a washing machine door won't open if a) not enough time has passed since the end of the cycle to the door unlocking itself, in which case you'd wait till for the unlocking click. You could also just switch the machine off, then switch off the power to it, then wait for 30 seconds before switching on again. OR b) the level of water inside the drum is too high. Have you checked that it has drained properly? Or if there is any blockage in the filter (usually behind a square panel bottom front of the machine), which may need cleaning out. Or a blockage in the drainage hose (at the back and connected to your water to drain pipe). Also, on some models, where you'd access the filter (and clear the fluff out from), there is often an emergency door opening lever beside it which you have to put down. But this should be a last resort. If you do have to use it, you have to reset the machine after by switching off power, waiting for 30 seconds then switch power back on again. Hope this helps and one of them works.

Zanussi Washing... | Answered on Mar 02, 2020

try a new fuse in the plug 13amp eric

Zanussi Washing... | Answered on Jan 13, 2020

Here is a video just for you...

Zanussi Tricity... | Answered on Dec 09, 2019

more than likely the defroster inside the freezer has gone bad. This defroster is located in the space between the fridge and freezer and activates to defrost the freezer and stop build up of ice in the freezer.. If it is bad the freezer will not keep the fridge nor freezer cold.

Zanussi 3.46 cu.... | Answered on Oct 03, 2019

broken circuit in printed circuit board

Zanussi Washing... | Answered on Sep 16, 2019

This sounds like doorlock issue.
You can access it from the door panel.
Panel has 4-6 screws.
From there you can check it with a multimeter (ohm setting).
It could also be as simple as bent door hatch, door lock not engaging with doorlock.

Zanussi Washing... | Answered on Sep 10, 2019

Broken parts will have to be replaced before reinstallation.

Zanussi... | Answered on Sep 08, 2019

Rinse Aid and Salt do not clean. Salt is a water softener, Rinse Aid drying without streaks. What about detergent?

Make sure the arm spins.

Zanussi... | Answered on Aug 26, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Zanussi Experts


Level 3 Expert

85239 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

33002 Answers

ray gallant

Level 3 Expert

68294 Answers

Are you a Zanussi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides