Whirlpool Cabrio - Recent Questions, Troubleshooting & Support - Page 9

Hello & Welcome to FixYa

Error code 5d/Sd means suds have been detected. To solve this problem you have to take the bottom front panel apart and then clean the drain filter pump assembly completely, make sure the washer is unplugged before working on it. Please get back to me if you have any other questions.

Kevin

being un-level could certainly cause it im currently working on this problem for another customer on this site while i haven't had hands on with this model yet i just finished reading the service manuel on it its kind of an amazing concept in washers if either one of you are on line reply to this message hold my rating for now as i need to ask some questions

There might be two possible reason for that.

it might be coming form the tub itself passing through the rubber seal of your plastic rotator(the big wheel inside the tub)

the other thing is in the junction of the hose the tub.

try to open the back of your washing macjine where you can get an access inside the wheel and the junction connector, from there you will the cause of the leackage. try to put some water while looking at so you can see where the water is coming out

Good Day, Your washing machine is fully automatic? the washing cycle is normal? if yes do the same maybe it will help you. for the fully automatic washing machine mostly have drain pump, please check the filter of your drain pump, how? remove the cup of your drain pump like a ordinary cup, screw it clock wise or counter clock wise. Remove drain pump filter and clean it, some hair pins, cotton buds or coins or any small item that coz of clog up. if your washing machine dont have drain pump ,but fully automatic check the drain motor if running or not? how? open the back cover for top loader washing machine only, select spin cycle and press start to see the drain motor running? the drain motor is like a small box with small wire to pull the lever of the drain to remove water inside, if the motor running or pull the lever of the water pipe but water still inside the washing machine, remove the drain cup or cover and clean it or check if have coin or cloth inside that coz of clog or water stuck, if the drain pump or drain motor is weak this is will cause and long time draining or totally not running the drain pump or drain motor and its cause of totally stop the cycle of washing machine in rinse time or spin time, because all fully automatic washing machine, after washing cycle the drain pump or drain motor must be on, to remove water before start the next cycle. rinse or spin cycle.

They are not in your agitator. they are in the pump on the bottom left if you are standing behind the machine. Be VERY careful. That litle pump seems to be the beginnig of many leaking problems.

Long fill

Whirlpool Cabrio F1 error code - NOW A RECALL ISSUE! model # WTW6600SW2
Call Whirlpool or a repair center. The number for Whiripool is 1-800-253-1301

Whirlpool Cabrio F1 error code - NOW A RECALL ISSUE! model # WTW6600SW2

• I called Whirlpool 1-800-253-1301 today 10/15/08 and they said the F1 issue is now under a recall.
• Whirlpool scheduled a repair service -during our phone call- to repair this under a 'recall' & at 'No Charge' to me.
• I'll let you all know how it goes after the repair..

F1 means the control board is shot. Call whirlpool and they should take care of the parts and labor even though your machine is out of warranty.

We have the same problem with our BRAND NEW Cabrio - and those white dusty spots with our old washer were a major reason for getting a new washer. Very disappointing. I believe the white dust is also on light clothing but we can't see it. Since most of the "answers" are obviusly wrong (we already use liquid detergent, already use the auto dispenser, and nothing is blocked because ti's BREAND NEW), we've taken to wiping down the washer basket before we run our clothes. It seems wasteful to run Afresh every week before we do laundry. But wiping out the drum with a cloth works.

If you turn off the hot water line, and you have cold water then suspect the water inlet valve. Unplug the unit and turn off the water to disconnect the water hoses. Pull out the washer and remove the back of the unit by the water hose inlet. The new valve is around $65.00 and is on connectors, which make it an easy fix.

sounds like the bearing is tarting to get worn out

Check your bearings. This post will show you most of what you need to know about your bearings:http://www.squidoo.com/how-to-replace-bearings-in-a-whirlpool-cabrio-maytag-bravo-or-kenmore-oasis

If you mean its leaking anytime you have water in the drum,the first thing to check is the drain hose connection at the back of the washer,You'll want to do this with the washer pulled out,(don't let the drain hose drop below the water level or you'll have a mess)If its not leaking there you should be able to look under the washer & see which connection it is(usually the inlet to the pump) Might be as simple as tightening the hose clamps.Hope this helps

Either your drain pump has failed or there is a coin or other object in the drain pump stopping it from pumping. I have both cleaned and replaced many of these pumps. Hope that helps.

LD is a long drain error.
Clean the lint out of the drain pump.

Hai, put a new capacitor to give it more power

Unplug it again and reboot?

Hi A Door Lock Error occurs if the door cannot be locked. It will try to lock it six times before displaying the error code. It has happened because Door lock mechanism is broken or removed from door. It may also happen due to Door switch/lock unit failure. To resolve the issue follow these steps---1. Unplug washer or disconnect power.2. Check door switch/lock unit.3. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU).Hope this helps...Please post back if you need more information. Daniel