Whirlpool Dishwashers - Page 7 - Answered Questions & Fixed Issues

Du1145 will not work

frist turn power off to diskwasher then back on see if the button start working if none the button will not work you made need replace the touch pad,some model come with the control panel all in one some are separately.

Whirlpool... | Answered on Dec 23, 2017 | 80 views

1 Answer

Need a reset sequence for Whirlpool dishwasher Model numberDU1ooXTPQ8 the normal and light load lights are rapidly blinking and it will not start or cancel out

f6 is no water coming in dishwasher check inlet valve an flow valve to cancel open door press start button untill the led go out an close the door the washer should reset an go back working

Whirlpool... | Answered on Aug 02, 2018 | 3,718 views

1 Answer

Whirlpool Quiet Partner DU1100XTPQA doesn't drain at the end of the cycle

check drian hose make sure it clear are the check valve made have item block it from closing ok are you made have some trash stuck in pump impeller

Whirlpool... | Answered on Dec 21, 2017 | 65 views

1 Answer

New Whirlpool dishwasher will not start for first use. Set choice of cycle, light came on, pushed start and lights out in 2 min. Did 2nd time not using start/

Check the door latch switch make sure nothing blocking it also check the water float inside once I found some shipping phone stuck underneath it making it think it was over filled

Whirlpool... | Answered on Dec 20, 2017 | 46 views

1 Answer

Whirlpool Quiet Partner 3 goes through the wash cycle but dishes on top rack are still dirty and there are food specks up in the cups afterwards, any suggestions or fix?

Customer service/utube

Whirlpool... | Answered on Dec 13, 2017 | 152 views

1 Answer

Whirlpool Dishwasher starts for 5 sec. then quits for hours. reset breaker and it will not start again for 5 sec

Most likely a fault (short circuit or ground fault ) within the heating elements of the dishwasher. Although the house circuit breaker will reset within a minute or so (manually of course) the built in protective devices will take more time to cool down.

Whirlpool... | Answered on Dec 06, 2017 | 68 views

1 Answer

Hello.have whirlpool dishwasher 4404/5. green light flashes x 4

sorry...

This is the WRONG PLACE for paid advise...

You need to contact the CLOWNS who charged you...!!

FIXYA is entirely FREE... (all volunteer)...

Not ever to be confused with money grubbers...!!

Good luck with your scammers.

Carnac the Magnificent

Whirlpool 24 in.... | Answered on Dec 03, 2017 | 104 views

1 Answer

Salt level doesn't work

I assume you are talking about a water softener. Mine runs off a timer - it is set to do its thing about 3 in the morning. If it is yours, check to make sure your timer is working (old motor and gear style or electronic, either could go bad) but if it is a rental unit, call them.

Whirlpool... | Answered on Dec 02, 2017 | 25 views

1 Answer

I have a Whirlpool Model

don't know if it'll help but won't hurt to unplug it for a couple of minutes and see if repluging it resets the unit. good luck.

Whirlpool... | Answered on Dec 02, 2017 | 70 views

1 Answer

Spotting glasses and silverware after

Find out why the upper arm isn't moving. It may be partially plugged. This would be the cause of the spotting.

Whirlpool... | Answered on Nov 29, 2017 | 92 views

1 Answer

I have a Whirlpool Quickwash

Look at the filter screen to see if anything large got past it and into the pump.

Whirlpool... | Answered on Nov 29, 2017 | 174 views

1 Answer

Why is my whirlpool dishwasher showing a tap symbol

Even though this video is for a different dishwasher, it gives you the ideas on what to check for. Basically the dishwasher is either getting no water or not enough water.

Whirlpool... | Answered on Nov 29, 2017 | 142 views

1 Answer

Dishwasher door leaks on the left side at the

Hi there... Try the simple things first. Quite often Fridges and dishwashers (with flat front seals) will start to leak if the body of the unit is distorted. This frequently happens if the supporting feet are not adjusted properly when setting up the unit in the first place. After a while the cabinet will begin to 'sink' in one corner which distorts the flatness of the whole front of the frame, allowing leaks. Try cranking up the foot nearest the leaking seal and see if it makes the leak better or worse. If worse, then crank up the opposite foot. Good luck.

Whirlpool... | Answered on Nov 25, 2017 | 588 views

2 Answers

Whirlpool dishwasher arms most of the time do not spin

hi bego.
as brian williams has told you thats what you should try.but if you want more info then read this.but i think you will find brian is right in what he is saying to you.
Dirty Filter/Pump. The power to spin the arms is usually related to the water pump for the dishwasher, but if the filter and pump are clogged, they won't put out enough pressure to operate the machine properly.