Whirlpool Dishwashers - Page 3 - Recent Questions, Troubleshooting & Support

0helpful
2answers

Whirlpool dishwasher leaks on the wash cycle

Where is it leaking from? It'd it is under the door, check the door gasket for tears.
11/26/2019 3:38:44 AM • Whirlpool... • Answered on Nov 26, 2019
0helpful
1answer

Whirlpool quiet partner II starts and stops. What should I check?

the first thing to do is unplug it for 3 minutes then check to see if it reset by running
11/22/2019 1:53:49 AM • Whirlpool 24 in.... • Answered on Nov 22, 2019
0helpful
1answer

Why does the inside of my brand new Whirlpool Dishwasher Model Number WDF130PAHWD remain very wet after washing the dishes? We have tried heat dry and Jet Dry. Still, housing remains wet.

i don't know. as it is new, i would call the seller or the manufaturer to see if this a normal condition or if a free service call is necessary.
10/26/2019 5:54:06 AM • Whirlpool... • Answered on Oct 26, 2019
0helpful
2answers

Whirlpool Spray Tower

I got the same problem and spent a couple of days trying to figure it out. The solution is extremely simple - you just snap the tower to the bottom tray. You need to lift the tray, insert the tower through the middle cell of the tray, and just snap it on it. That's it - no bolts, no connectors, nothing.
10/19/2019 12:55:15 AM • Whirlpool 24 in.... • Answered on Oct 19, 2019
0helpful
1answer

Whirlpool DWF 417 soap dispenser door won't shut

cycle timer. Mine wouldn't shut if timer were in the wrong place.
9/5/2019 3:44:17 PM • Whirlpool... • Answered on Sep 05, 2019
0helpful
1answer
0helpful
1answer

What component does the hot water supply connect to in a whirlpool dishwasher?

Please check your normal water supply it's above 35'c no need to contact any component
7/19/2019 2:03:26 AM • Whirlpool... • Answered on Jul 19, 2019
0helpful
2answers

Whirlpool Quiet Partner II clean light blinks 7

The clean light flashing 7 times is an error code indicating an issue with the wash temperature. If the control does not detect a 4*F temperature rise in the main wash cycle, it will display the fault as the clean light flashing 7 times. There are several things that could cause the water not to heat, including the water being too hot coming in, an open door switch, or a faulty component in the heater circuit. The most common cause is the door switch not closing properly. This can be due to a loading issue or a latch issue. If upon visual inspection of the heating element no obvious defects are found, I would recommend resetting the control and running another cycle, paying close attention to door closure. If the light begins flashing again, you likely have a component failure. The heat circuit consists of several components including the element, control, door switch and tub thermostat(s). Reset the control by pressing teh following buttons within 5 seconds. Hit Temp Wash Heated Dry Hi Temp Wash Heated Dry.
7/17/2019 7:04:11 PM • Whirlpool... • Answered on Jul 17, 2019
0helpful
12answers

WHIRLPOOL DISHWASHER, ERROR CODE 4,

I have the solution! Had error 4 and had the repair guy come....he said its caused by too many suds...if you are using tablets that have rinse aid as well as rinse aid, it causes to many bubbles, these get sucked down the two little outlets (located at the bottom of the dishwasher door, easy to see if you open the door completly) and make the water level in the base seem higher than it actually is which triggers the over flow button. Now to fix it is SUPER hard....NOT! Just pull out your dishwasher, and tip it back slightly. The water stuck in the base will trickle out...not much but will take 5-10 mins. Then turn it on, run on a rinse cycle to be sure its all gone! Easy Peesy. I called whirpool about this, and why they could not tell me how to fix it is beyond me......they told me to press and hold the start button...i dont think even they know how to fix it! So...I got to do this under warranty, now hopefully you get to fix it for free and we all win. Yay!
7/11/2019 3:15:58 PM • Whirlpool... • Answered on Jul 11, 2019
0helpful
1answer

Whirlpool Quiet Partner ii lights stay on after the cycle is complete. when I go to start a new cycle it will not allow me to select a washing cycle, or does not allow the start button to activate.

Are you sure the cycle is complete?
If it is drying dishes then you will be interrupting the cycle. It is possible to cancel cycle and start over.
6/27/2019 12:29:04 AM • Whirlpool... • Answered on Jun 27, 2019
0helpful
1answer

Whirlpool adg 7470/1 water not draing away

Please click the link below and follow the procedure carefully on how to fix a clogged diahwasher

https://www.whirlpool.com/blog/kitchen/how-to-fix-a-clogged-dishwasher.html

Hope I was able to help you.
6/16/2019 2:57:39 PM • Whirlpool 24 in.... • Answered on Jun 16, 2019
0helpful
1answer

I have a Whirlpool Quiet Partner II and the normal and hi temp wash lights are blinking. I've tried the reset code by pressing the heated dry and normal buttons but this hasn't made the blinking stop.

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. It could be a corrosion problem: My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 11:09:44 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

W10073650 Whirlpool Dishwasher--Start button just flashes when I push it and won't start machine. Any advice?

It could be corrosion at P1 connector. There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:56:35 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

Pots/pan light blinks alternately with the normal wash button.

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. It could be corrosion at the P1 connector: My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:54:04 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

Normal wash light continually flashing

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. It may be corrosion in the low voltage connector. My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:46:42 PM • Whirlpool Gold... • Answered on Jun 14, 2019
0helpful
1answer

My control pannel is showing

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. However corrosion may be causing this: My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:42:58 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

Whirlpool dishwasher GU2800XTVQO delay lights won't stay off. Tried turning circuit breaker off for 30 min turned back on same thing. Started wash ran for awhile stopped when delay light came on.

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault, but it may be corrosion in the low voltage connector. My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:41:56 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

I have a quiet parner whirlpool dishwasher and the clean light is blinking

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps to determine which component is at fault. My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:37:33 PM • Whirlpool... • Answered on Jun 14, 2019
0helpful
1answer

My whirlpool gold start button won't start at all it gives me a (start ?) and won't turn on at all. I hope you can help. Jen

There is a trouble shooting document behind the kick panel at the bottom of the machine. Follow the steps. My whirlpool dishwasher gold GU2475XTVQ0 had rapid blinking lights that started with the "4 Hour Delay" LED and changed to others when other buttons were pressed. The machine would not run. I followed the instructions located behind the kick panel and verified the keypad was the issue and not the control circuit by elimination. The big surprise for me was that when I used a straight pin to resistance check all of the buttons, they checked out OK. I reconnected the 14 pin connector (P1) to the control and found that the buttons/LEDs were behaving correctly! I believe that pushing the straight pin into the 14 pin connector removed any corrosion in the 10 year old device and permitted the keypad to communicate with the control again. I reassembled the dishwasher door and it ran with no problems. I was ready to replace the keypad for $150, but didn't have to!
6/14/2019 10:33:48 PM • Whirlpool... • Answered on Jun 14, 2019
Not finding what you are looking for?
Whirlpool Logo

6,998 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Oloyede Monsuru

Level 3 Expert

1468 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...