Whirlpool Dishwashers - Recent Questions, Troubleshooting & Support

0helpful
1answer

My Whirlpool 7470 dishwasher does not complete a cycle

What does the flashing light say on it. Is it a symbol or word. If the cycle is incomplete and light flashes 8 times, it could be telling you the error code. Is water left inside the tub. Let me know how the light reads.
NEVER MIND I found the problem. You mentioned shortening the drain hose. When the light flashes 8 times, it could mean 1 of 4 things. Here is what the manual says. The drain hose must make a loop and reach the height of the dishwasher and back down in the disposal or drain. If it doesn’t, the dishwasher will siphon water from the hose and back in dishwasher. When water is gone from the hose, it will draw in air. Fix the problem by putting everything back the way it was.
9_29_2022_8_12_02_am.jpeg
9/29/2022 8:29:09 AM • Whirlpool... • Answered on Sep 29, 2022
0helpful
1answer

18" Whirlpool dishwasher humming. What to fix?

Hey, thank you for the question. According to my research the problem is most likely with its Rear Drum Support Roller Kit, part number 349241T. if this is not fixing the problem then the problem is most likely with Idler Pulley, part number WP691366. I hope this will fix your problem.
9/24/2022 4:25:39 PM • Whirlpool... • Answered on Sep 24, 2022
0helpful
2answers

Whirlpool adp 6515ix dishwasher start button is flashing in 4 time cycles-what does this tell me please. None of the manuals indicate what the flashing could be signalling.

Error CodeConditionCheck/RepairShop PartsClean light blinks 7 timesHeater circuit failure. Control didn't detect the expected rise in water temperature.Check the heating element and related components (wiring and control board) in that circuit. Heating element, Electronic control board, Thermistor, Circuit wiring Console light blinks rapidlyThe control detects a stuck button on the control panel.A failed control panel or a malfunctioning electronic control board can cause this code. Check the buttons on the control panel using a volt/ohm meter. In most cases, the control panel must be replaced. If that doesn't solve the problem, the electronic control board might be at fault. Control panel, Electronic control board Start/Resume light blinks slowlyIf the dishwasher door is opened or power is interrupted during the cycle, the dishwasher won't start again until the door is detected as closed and the Start/Resume button is pressed.Check the door latch and switch assembly. A failure in the Start/Resume button also can cause this problem. Door switch assembly, Control panel, Electronic control board Clean light stays onThe dishwasher won't start a new cycle unless it detects that the door opened after the previous cycle.Turn off power to the dishwasher by shutting off the breaker and restarting. If that does not work, the door switch assembly is stuck and must be replaced. Door switch assembly Control lock LED is on but not accepting key pressesAccidentally turned on or control detected keypad problem.Press the Heated Dry key for 5 seconds to turn off control lock feature. If that doesn't work, replace keypad. Keypad Sanitized LED blinks at end of cycleControl couldn't confirm that the dishes were sanitized.Check voltage to the dishwasher and the temperature of incoming water. Check the diverter motor, the heater and the OWI/thermistor. Diverter motor, Heater, Thermistor
8/13/2022 7:21:09 AM • Whirlpool... • Answered on Aug 13, 2022
0helpful
2answers

The normal cycle light on the whirpool WDF518SAAM, stays on and the dishwasher does nothing.

Any fault code? Is the inlet tap open?
8/2/2022 5:57:39 PM • Whirlpool... • Answered on Aug 02, 2022
0helpful
1answer
0helpful
1answer

Whirpool dishwasher ADPS 5540 shows F8 E1 after 30 minutes

turn off the water and remove the hose at the rear of the machine. Inside you will find a small wire gauze strainer. This blocks with limescale and debris from the water mains, just enough to reduce water flow below the thresholds.. E1 F8 Whirlpool dishwasher If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It's possible the drain hose extends more than 4.5" (114 mm) into standpipe. Apr 5, 2021

F8 E1 Error Code for Top Load Washer - Product Help

6/26/2022 3:58:06 PM • Whirlpool... • Answered on Jun 26, 2022
0helpful
1answer

Dishwasher shuts off mid cycle

Hi Ray. i found this out. The reason for the dishwasher to stop mid cycle is that the thermal fuse is shorting out because it is either fouled, dirty, broken, or loosely connected. If your dishwasher is older, the thermal fuse is used as a safety switch to stop the motor and circuit board when the dishwasher gets too hot. or go to this link might help you out. https://fixappliances.ca/dishwasher-repair/why-your-dishwasher-starts-and-stops-during-wash-cycle-and-how-to-fix-it/#:~:text=The%20reason%20for%20the%20dishwasher,the%20dishwasher%20gets%20too%20hot.
6/16/2022 6:12:18 PM • Whirlpool... • Answered on Jun 16, 2022
0helpful
1answer

Does anyone know if whirlpool has fixed its friction pad problems with them breaking constantly on its dishwashers?

If you are in the UK and purchase a Hoover machine, parts are warranted for 10 years.
5/4/2022 6:42:35 PM • Whirlpool... • Answered on May 04, 2022
0helpful
2answers

We have a Whirlpool Quiet Partner II Energy Star 8575637. Foam flows outside the diswasher.

You just need a new door gasket and it is a cost effective repair if it still works okay for about $20. https://www.google.com/search?q=Whirlpool+Quiet+Partner+II+Energy+Star+8575637+door+gasket ..
2/11/2022 8:56:02 PM • Whirlpool... • Answered on Feb 11, 2022
0helpful
2answers

Hi, the dishes on the top rack of our Whirlpool Quietmaster III do not dry completely, but the bottom dishes are fine. We have to re-wash the upper rack dishes; they have spots on them. Ron.

Make sure the top spray arm is turning! check for blockage in the jets at the very end of the spray arm, or that the spray arm has not split. Put the arm in a known position, and check it has moved after a few moments. Remove blockages or replace the arm if necessary. These machines dry only by the last rinse being in hot water, then the plates drip dry. Are you using rinse aid? this helps the water to disperse without spots.
1/18/2022 11:06:50 AM • Whirlpool... • Answered on Jan 18, 2022
0helpful
1answer

Whirlpool Dishwasher WDT710PAYM0. 5 years old. Won't start. When we hit the start button, we get 15 beeps, then nothing.

Hi Peggy, could be bad door latch. The door latch keeps the door closed and the water inside while the dishwasher is operating. The door latch is connected to a switch, which will not allow the dishwasher to start unless the door is properly closed. Best, Dave
12/22/2021 11:06:38 PM • Whirlpool... • Answered on Dec 22, 2021
0helpful
2answers

Dishes constantly come out dirty..

Supply water temperature should be above 120 degrees F for effective cleaning. Run hot water from your kitchen sink (your dishwasher should be tapped off the hot water line near your sink faucet) right before you start a dishwashing cycle to make sure it's as hot as it can be when the dishwasher begins filling. Also, during the wash cycle the heating elements at the bottom of the tub may turn on and warm the water further even if you select a "No Heat Dry" option causing a noticeable shot of steam to escape if you open the door during a cycle.
Note: I recently had a problem with our dishwasher (Frigidaire FDB834RFS0) causing dishes to come out dirty and the detergent dispenser to be left with undissolved detergent. Our problem happened to be caused by a partially clogged strainer in the water supply valve. (I would imagine Whirlpool most likely has some kind of filter/strainer in its water valve as well.) When the supply valve was commanded to open for some time, I noticed the water level in the tub would barely be visible below the lower spray arm. After cleaning out the strainer (required removing and disassembling the water supply valve) the water level was noticeably higher -- almost at the bottom of the float or about an inch below the heating elements. Our dishes and the detergent dispenser are now clean.
If your water supply is ok, I would next check to make sure your spray arms do not have any plugged holes and that they rotate freely. Also, use a good quality detergent and a rinse aid. We prefer liquid Cascade and Jet Dry. We have had problems with old, stale, or really thick liquid detergents and by getting a fresh jug have solved the dirty dish dilemma.
Make sure to clean out the filter basket at the bottom of the basin below the lower spray arm occasionally as it can clog and cause the pump to starve due to lack of water. If the pump can't get a supply of water to pump to the spray arms and nozzles, your dishes will not get sprayed evenly and you will end up with them being poorly cleaned.
Hope this helps you out...good luck!
12/1/2021 2:50:31 AM • Whirlpool... • Answered on Dec 01, 2021
0helpful
2answers

Whirlpool dishwasher not spraying water during wash cycles Model #: WDT730PAHZ0

Check water pump and make sure there is no bloks in the pipes try using a good dishwasher cleaner and if its got the turn bit on base inside open it and make sure filters are clean blessings
12/1/2021 1:00:32 AM • Whirlpool... • Answered on Dec 01, 2021
Not finding what you are looking for?
Whirlpool Logo

7,012 questions posted

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4383 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Cindy Wells

Level 3 Expert

6528 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...