Water Heaters - Page 4 - Answered Questions & Fixed Issues


the common cause of that is you have higher water pressure at your sink tap..and have lower water pressure at your shower.. because your using a multi-point type water heater..it requires 2.0 ltrs/min..
you do this...try to open your shower together with your sink tap faucet.

Water Water... | Answered on Dec 05, 2019 | 104 views


some heaters are there's and indicator of reset button on the unit..and some are located inside the unit can be push by using screwdriver.

Water Water... | Answered on Dec 05, 2019 | 99 views


did you put in a new pump or us old one and did they go deeper than old well .new faucets have pressure regulators built in for safety purpose

Water Water... | Answered on Nov 25, 2019 | 105 views


call your local plumbing repair service we never said we know every thing about every make made world wide .

Water Water... | Answered on Nov 23, 2019 | 97 views


Well, unless you share with us what the problem is, and what make and model you have, we can't help other than to say call a plumber locally to look at it.

Water Water... | Answered on Nov 20, 2019 | 98 views


If you mean the red button you have to press when you light the boiler, then it mean that either the thermocouple needs replacing or the shroud over the flame has moved or burned through. Either way, you need a registered gas installer to fix.

Very unusual to have a heater with a remote control. Did you try changing the batteries as they may be low in power?

Advanced electronics
Every Richmond model is electronically controlled for precise temperature control, and self-diagnostic, great for maintenance and troubleshooting. The temperature of the outgoing hot water is factory set on 120 F, but by using the remote control you can easily set it in the range from 100 F to 140 F. The temperature and error codes are shown on the digital display of the remote controller.

You can Contact Richmond direct from here

https://www.richmondwaterheaters.com/contact-us/

Water Water... | Answered on Nov 14, 2019 | 147 views


You didn't mention the type of paraffin heater you are using, which might have been helpful.

Clearly water has contaminated the business end of the heater and oil and water do not readily mix. It should be possible to mop most of the water out of the works using absorbent paper, even if it means partially dismantling it and then relight it and persevere - the heat should evaporate the remaining water eventually.

Various companies can provide an emulsifying agent which could help with your problem. Something like Wynns Dri-fuel is designed to deal with water contamination in vehicle fuel tanks. There are other brands, usually from industrial suppliers but the Wynns product is widely available in smaller quantities.

If the heater remains stubborn after being mopped and dismantled you could brush a little Dri-fuel around the business end of the heater and add a little to the fuel - though make certain it is fully mixed...

Water Water... | Answered on Nov 13, 2019 | 95 views


ASK THE MFG OR GOOGLE THE ERROR CODE

Water Water... | Answered on Nov 05, 2019 | 104 views


Do you have one handle, if you do replace the faucet with dual handle faucet. A single handle faucet has built in valves which mix the hot and cold water as you change position of the handle.

Water Water... | Answered on Nov 04, 2019 | 118 views


turn off gas to heater and drain unit of water so it don't freeze

Water Water... | Answered on Nov 04, 2019 | 107 views


You will have to ,So you can repair it

Water Water... | Answered on Nov 04, 2019 | 106 views


there is probably sediment stuck in it and it needs to be replaced

Water Water... | Answered on Nov 02, 2019 | 106 views


Troubleshoot resources for power vented water heaters and intellivent gas control valve on following link:
http://waterheatertimer.org/power-vent-water-heater-troubleshoot.html#intellivent

Your hot surface igniter has to be lined up in front of a gas port ... if no gas is coming out, the intellivent gas control valve should shut down heater and cycle for several attempts before issuing error code ... sounds like gas control is bad..

Water Water... | Answered on Oct 28, 2019 | 106 views


A typical answer for thisĀ·

1. Cut off power to the water heater at the panelĀ·
2. Check the water heater reset button- The water heater reset button is the red button situated on the water radiator itself (simply over the indoor regulator). Some water heater may have two reset catches one for each indoor regulator. To get to the reset catch, you may need to evacuate the metal plate covering the indoor regulator that is held set up by screws. You may likewise need to evacuate a rectangular bit of froth protection to see the reset catch(button).
3.DO NOT reset if safety features continuously trip.

For More Information You Can Visit: https://www.indiapropertyclinic.com/services/water-heater-install-repair

Water Water... | Answered on Oct 15, 2019 | 148 views


Use a digital volt/ohm meter to check voltage at the water heater.

Water Water... | Answered on Oct 13, 2019 | 114 views


Most common problems are clogged spray nozzles, and heating element. Due to hard water post use residue. Always flush with warm clean water using a bucket the upholstery brush attachment.

Water Water... | Answered on Oct 09, 2019 | 118 views

Not finding what you are looking for?
Water Logo

Ask a Question

Usually answered in minutes!

Top Water Heaters Experts

Don Walper

Level 1 Expert

36 Answers

Cindy Wells

Level 3 Expert

6136 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2020 Answers

Are you a Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...