Vtech Lands Phones - Page 9 - Popular Questions, Answers, Tips & Manuals
How do i change from spanish to english on my vtech phone
Try this: ( tested on a CS6429 )
press [menu]
scroll to "> Settings"
press [select]
scroll to "> LCD Language"
press [select]
scroll to "> English"
press [select] ( chirps ) press [OFF]
press [OFF] again to return to "Handset #"
Note: on the CS6629 handset, it will ask for
confirmation "Set English?", press [select]
Good luck!
------------
How do I change the announcement on the phonr
Try this ( tested on CS6429 & CS6629 ):
press [menu]
scroll to "> Answering Sys"
press [select]
scroll to "> Announcement"
press [select]
=== follow the instructions displayed & aloud:
=== eg, "To Record, press [7]"
when finished speaking, press [OFF] to exit
press [OFF] several times to backup to "Handset #"
Good luck!
------------
Can not register handset
The handset must be de-registered before it can be registered.
Try this:
1. To de-register the handset from another base:
When the orphaned handset says "Connecting..." or
"Out of Range..."
enter *331734 [menu]
and it will soon beep and display "Not registered"
2. To register the new handset to your base:
press the "Handset Locator" button on the base and hold
it until the "in use" light comes on ( ~ 4 seconds ),
then release the button and set the new handset into
the base phone cradle. After ~ 30 seconds it will beep
and display "Handset #" (next in sequence).
3: Note: the base handles a maximum of 12 handsets.
If your system was fully populated ( ie, a handset is
already # 12 ) you will have to clear all the handsets
from the base and re-register them all in sequence.
( it is the only way to 'rescue' the places occupied
by the lost handsets ).
To clear the base of all registrations:
1. Press and hold the the "Handset Locator" button
until the "in use" light lights and then starts to blink
( ~ 10 seconds ), release the button --
then press it again briefly while the "in use" light
is still blinking.
2. The base will beep and all handsets that were registered
will display "Not Registered"
3. Follow the instructions above for each handset
in turn to re-register them:
press "Handset Locator" ~ 4sec ( in-use light on ),
set handset into the base cradle, etc.
The manual is available from:
www.manualslib.com
but does not fully describe these procedures.
Good luck !
11/22/2015 2:33:35 AM •
Vtech AT&T...
•
281 views • 0 helpful votes
Have a replacement handset, base is cs6729-2 handset is cs6729-3 how do i set up new handset to see base?
This sounds like a registration problem, the new
handset must be de-registered from its original
base and then registered to your base.
NOTE: the CS6729 handles a maximum of 5
handsets. If you have a handset displaying
"Handset #5" then you have a 'fully populated system'
even if you actually have only one or two handsets.
You will need to clear each handset ( I ) then clear
the base of all registrations ( II ) before re-registering
each handset ( III ) up to the maximum of five.
=====================================
( I ). First, to de-register a handset ---
0. Start by taking off the battery compartment cover.
1. press [menu]
2. scroll up/down to "Settings"
3. enter * 7 8 9 0 #
4. scroll down to "next page", press [select]
5. scroll down to "Register Clear?", press [select]
6. display asks "Confirm?" or "Register Clear??",
press [select]
7. display reads "Ok" and chirps, press [ off ]
8. UNPLUG THE HANDSET BATTERY
(this is why the cover was off)
9. Wait ~30 seconds, re-connect the battery &
replace the cover
10. display reads "Not Registered"
===============================
( II.) To clear the base of all handset registrations
( if needed, else skip ahead to ( III ). )
1. press [Find Handset] on the base and hold
past ~4 sec when the "In Use" lamp lights, at
about 10 secs the "In Use" lamp will begin to
blink.
2. release the [Find Handset] button momentarily,
then briefly press it again. After a moment,
all handsets that were registered to the base
(if any) will display "Not Registered" and be
ready for fresh registration
===============================
( III.) To register each handset to the base:
1. press [Find Handset] on the base and hold for
~4 sec until the "In Use" lamp lights.
2. press # on the handset and set the handset into
the handset cradle on the base
3. within 30 seconds or so, the handset will either
chirp and display "Handset Registered", then
"Handset #x" or it will say "Registration Failed".
NOTE: the battery must be well charged prior to the
registration process, a weak battery may cause a
"Registration Failed". Charge the battery for a
few hours and try the registration ( III ) again.
===============================
Good luck !!
Model cs6419-2. How do I set up voice mail?
Voice Mail is a service sometimes offered by the
Telephone Service Provider (whom we used to
call "the phone company").
Call your telephone service provider and ask them
to explain how to manage their "voice mail features".
Good luck!
------------
How do i get the vtech server to dowload the server
Search Results
https://my.mcphs.edu/.../full_vtech_student_login.pdf
MCPHS University1) Open your web browser and go to https://vtechcenter.mcphs.edu ... the bar and choose "Download File" from the drop-down box ... Connection Server.
motherboard.vice.com/.../one-of-the-largest-hacks-yet-exposes-data-...
ViceNov 27, 2015 - The breach of the popular kids' gadgets company VTech is the fourth ... after a hacker broke into the servers of a Chinese company that sells kids ... where parents can download apps, ebooks, and games for VTech products.
Not finding what you are looking for?