Where is the escucheon located
this is the plate behind the handle or it is the plate that is on the shower head arm itself its the little circle plate that is againts the wall to hide the hole
What is a planting hoe?
A
planting hoe is a hand tool used for weeding and loosening the earth around
plants. It has a thin flat metal blade
attached to a long handle.
I have a pegasus thermostatic
I have a similar problem in a house I just moved into. It's clearly not an issue with the temperature settings because I adjusted those and it hasn't fixed the problem. Pressure is low and it's only hot water, which leads me to believe the cold water isn't making it to the faucet for some reason. Have you figured out a solution? I'm searching all over and can't find anything. It's maddening. Thanks.Bob
I accidently drield a hole in abrass pipe under
From basement,crawl space or cut an opening in floor,to get to the damaged pipe. If you can cut it, you may be able to pull it out from another location and feed new material back. Unfortunately your going to have to apply heat and solder, in a confined space under the floor. Not too good!
4/1/2010 1:00:48 AM •
Union Pipe...
•
Answered
on Apr 01, 2010
•
91 views
I cannot get the water hot enough and maitain the
pegasus is a home depot product u need to adjust ur anti scald setting the valve is shipped in cold position it should have a red and blue plastic clips that go over the grooved thing call pegasus customer service at 1888 328-2383 they should be able to assist u with ur problem if u need parts or how to adjust the anti scald system
Have a pegasus shower single valve ..cannot
when it is sold the anti-scold is set at cold to protect the buyer -the piece with the groves on it is the stem their should be two plastic clips a red and blue that slid over it these clips are the adjustment -also give pegasus a call they have an 800 number to assist u or home depot the carry the brand
11/11/2009 1:25:29 AM •
Union Pegasus...
•
Answered
on Nov 11, 2009
•
1,105 views
How to remove the back wheel of a union bike?
simply loosen the axle nuts on the rear axle (3/8 axle = 15mm or 5/8 wrench 14mm axle = 19mm or 3/4 wrench). then slide the wheel forward in the dropouts, and remove the chain from the freewheel/cog and chainwheel/sprocket. (be sure to do your best job at not tangling it or it will cause about an hour of headaches lol). then loosen the brakes using either the barrel adjusters or simply removing the straddle cable.then slide the wheel out. any more questions contact me directly.
8/18/2009 6:53:52 PM •
Union Cycling
•
Answered
on Aug 18, 2009
•
110 views
Pegasus schematics
there is another plumbing place called furgouson i think thats how you spell it,check my spelling,lol good luck.if they don't have it they most times can order it for you.
How to install 3/8 compression fitting? I can not
This is because the ferrul ring has been compressed on the pipe and is very tightly secured under the nut. There is a very handy puller available which will pull the nut and ferrul off of copper piping. Without the special tool you are probably going to be faced with cutting it off and starting over again if your project affords that room. If the nut and ferrul appear good can you stay using the existing nut and ferrul? If you have no room to afford cutting and starting fresh,the nut and ferrul can be split or cut off which is somewaht of a chore. Ive got a little dremel cutting wheel that splits them off fairly well but have to bevery painstaking not to damage the pipe with the grinder wheel
7/2/2009 4:00:57 PM •
Union Pipe...
•
Answered
on Jul 02, 2009
•
1,645 views
Not finding what you are looking for?