Uniden Lands Phones - Recent Questions, Troubleshooting & Support

0helpful
1answer

Uniden XDECT 8115 Home Phone. How do I cancel a selected ringtone?

Question edited for FULL 'make model (what it is)', and dreadful typo spelling of 'Uniden'. Question moved from Computers to Land Phones. https://www.google.com/search?q=Uniden+8115+manual ..
7/2/2022 3:52:25 AM • Uniden Cordless... • Answered on Jul 02, 2022
0helpful
1answer

How do I recharge the battery for my Uniden XDECT SSE45

swap hand sets after the first is charged. use SSE07 accessory handset and charger that is included in original set. https://uniden.com.au/wp-content/uploads/2017/07/SSE_45_OM.pdf
6/10/2022 6:03:57 AM • Uniden Lands... • Answered on Jun 10, 2022
0helpful
1answer

DCX170 handset will not register to DECT2060 Base

Yes, it looks they are compatible. I would guess you need to set up from scratch. Remove all power to base unit and handsets, batteries to handsets, and phone line and start from the Base unit, to powering handsets again. https://www.google.com/search?q=DECT2060+base%2C+with+DCX170+handset ..
4/26/2022 9:07:16 PM • Uniden Lands... • Answered on Apr 26, 2022
0helpful
1answer

How to register a new handset?

Unfortunately, the EXI5560 is not an expandable cordless telephone system. The base can only use the handset to which it was originally linked at the factory. Similarly, the DXA15588 handsets need to be paired to that base, not just to any Uniden cordless phone base. The first handset gets registered while it is charging in the main base. Charge the second handset fully in the charging base. Make sure not to use the phone for any incoming calls during the registration process. Take the first handset off the main base. You do not have to put this handset on the other charger and put second handset on the main base. Wait for the Charge/In Use LED to begin to flash. Wait at least another 5 seconds before removing the second handset from the main base. That's when you should be able to use the find HS button on the DXA15588-2 main base to get both handsets to beep. I hope this helps. You can find the manuals for these phones at the following sites: https://www.uniden.info/download/ompdf/EXI5560om.pdf and https://www.uniden.info/download/ompdf/DXAI5588-2om.pdf . Cindy Wells
4/7/2022 11:16:17 PM • Uniden Lands... • Answered on Apr 07, 2022
0helpful
1answer

What are the 2 (or 3?) buttons held down before switch-on on a Uniden UBC120XLT that displays a battery reading?

That scanner has a battery level indicator that is active when the unit is on, it flashes when the battery is low and there is no key sequence to display any battery info in the manner you described.
4/4/2022 3:41:29 AM • Uniden Lands... • Answered on Apr 04, 2022
0helpful
1answer

How do I initiate an intercom call from my Uniden cordless telephone to another unit on the same line

DECT 5.0 is the range. The model number will be on the base or rear of the base station. Have a look at the videos https://www.google.com/search?q=uniden+dect+6.0+intercom+feature ..
1/29/2022 4:37:37 AM • Uniden Lands... • Answered on Jan 29, 2022
0helpful
5answers

How do i use the intercom on my Uniden dect. 6.0?

March 25, 2013 - INTERCOM INSTRUCTIONSHere is the answer! Press the INTERCOM button one time.The INTERCOM display will show on the screen.Use the UP or DOWN arrow button to select the HANDSET number.Press the MENU/SELECT button to ring the HANDSET selected.Press the END button when done talking
1/7/2022 10:10:47 AM • Uniden DECT 6.0... • Answered on Jan 07, 2022
0helpful
2answers

Need to have a Mitel SX 50 Phone System ring on cordless phones

You can switch to "night" mode on the console and the incoming calls should ring on the cordless. try it.
1/4/2022 9:32:38 PM • Uniden 5.8GHz... • Answered on Jan 04, 2022
0helpful
3answers

I have a handset that will not register. It was

if you press talk what apperars on the screen of the handset that will not register?
12/17/2021 11:49:44 PM • Uniden CLX485... • Answered on Dec 17, 2021
0helpful
3answers

Mitel SX50 Equipment Busy Problem

Press "function", then 32. This will clear all alarms and error codes.
12/6/2021 2:24:08 AM • Uniden 5.8GHz... • Answered on Dec 06, 2021
0helpful
1answer

The base unit on my Uniden SSE25 is not recording incoming messages. How do I fix it?

we consumers can not fix them , bin it and get a new unit
11/29/2021 11:25:44 AM • Uniden Lands... • Answered on Nov 29, 2021
0helpful
2answers

How to put speaker phone on my uniden 6.0 phone

What model Uniden DECT 6.0 phone?
11/18/2021 8:51:21 PM • Uniden Lands... • Answered on Nov 18, 2021
0helpful
1answer

PHONE SAYS SEARCHING....WON'T CONNECT

11/13/2021 7:19:16 PM • Uniden Lands... • Answered on Nov 13, 2021
0helpful
3answers

My uniden phone says - out of range

Uniden wxi477 out of range fixThis problem arises when the handset does not communicate with the base.These are the steps:1: Deregistering the handset 2: Registering the handset to baseDeregestering clears the stored (incorrect) base information on the handset.Reregestering allows the base to assign a new ID for the handset.Deregistering- press and hold the OFF (red button) and the # button on the handset for 5 seconds. select base unavailable and press OK. Are you sure appears. select yes and press OK. you will hear a confirmation tone. The handset will delete its own base information without trying to contact the base. It will now display MODELS VARY PLACE HANDSET ON THE BASE FOR REGISTRATION.Registering the handset with the base- Make sure the tel. line and power is plugged into the base.Press an hold the register button under the base (located between the tel. line and yellow power socket under the base) for 5 seconds until the red light flashes. At the same time press and hold the # button on the handset for 5 secs. You will hear a tone and It will now display REGISTRATION COMPLETE.If it says registration failed: Retry the registration steps. Make sure the handset have enough battery power. If not charge for 15-20 hrs.Check your connections on the base and make it is getting power.The Steps above was my fix for the uniden wxi477 out of range problem.Good luck.
11/9/2021 10:26:24 AM • Uniden TRU9585... • Answered on Nov 09, 2021
0helpful
1answer

Need to reset Uniden base

HOLA tengo un problema con mi base tiene un error el n?mero 4 no se d?nde o c?mo solucionar el peo la E4 no enciende eso paso desde un corte el?ctrico si alguien me puede ayudarme
10/27/2021 4:01:56 PM • Uniden TRU9466... • Answered on Oct 27, 2021
0helpful
6answers

Panasonic cordless handsets all say line in use

I had the same problem. Something makes the phone's memory get "stuck."  Take the battery out of the phone for a minute and then put it back. Then unplug the phone and plug in again. You need to do this with all extensions. The problem goes away. 
10/26/2021 12:28:58 PM • Uniden Cordless... • Answered on Oct 26, 2021
0helpful
1answer

Uniden phone XDECT SSE47 When setting date & time for daylight saving time screen reverts to standard time after a call is made. How do I stop this reversion?

Do you have the time adjustment set to Caller ID? If so, the time is being reset when your phone connects to the telephone company computer. To set this see the Advanced Setup options. Make sure that the phone system is in standby when you press the Menu/OK button to access the menu system. See page 17 of the manual for the information on the Advanced Setup options. The manual is available here: https://uniden.com.au/wp-content/uploads/2017/07/SSE_47_OM.pdf . I hope this helps. My guess is your telephone provider either hasn't updated their clocks or otherwise is giving faulty time information. Cindy Wells
10/8/2021 10:37:12 PM • Uniden Lands... • Answered on Oct 08, 2021
0helpful
1answer

I have a uniden dect

Since you declined to specify the model of your Uniden DECT 6.0 phone, please select it from the list beginning at
http://www.uniden.com/owners-manuals/dect-phones/scat/dectphones_mnl/
to download a manual.
7/31/2021 5:21:07 PM • Uniden DECT 6.0... • Answered on Jul 31, 2021
0helpful
1answer

Uniden BCD436hp - messed up my settings. Is there a way to get back the settings that were set by the company, when i purchased? Thanks!

If you can access the menu system, try Settings > Restore Options > Clear User Data > Full Reset. A quick step to do this, Press and hold 2, 9, and Dept when you power on the scanner. In the Clear User Data menu, there is also a Reset User Settings. This keeps the Favorites list. See page 31 of the user manual available at the Uniden support page: https://www.uniden.info/download/index.cfm?s=bcd436 . The current link to the English version of the manual is https://www.uniden.info/download/ompdf/BCD436HPom.pdf . I hope this helps. Cindy Wells
7/29/2021 4:16:44 PM • Uniden Lands... • Answered on Jul 29, 2021
0helpful
1answer

Uniden xdect 8055 pairing phones

Xdect 8055 handset reset 1) Press and hold the hang up and # keys for at least 5 seconds. 2) Move the cursor to select Base Unavailable and then press Select. 3) Select the base you want to deregister from, press Select and then move the cursor to Yes and select. This causes the phone to delete any of its base information.
7/25/2021 2:12:42 AM • Uniden Cordless... • Answered on Jul 25, 2021
Not finding what you are looking for?
Uniden Logo

10,901 questions posted

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

Cindy Wells

Level 3 Expert

6490 Answers

Muzahura Frank

Level 3 Expert

2071 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...