Ultrex Blenders - Recent Questions, Troubleshooting & Support

If it cannot be purchased right from the maufacturer (which it likely won't as it is 11 years old), you can get nice blenders for around $20 at super stores like Walmart that work well and last for a while.

try e spares on the internet

I HAVE THIS EXACT MODEL AND HAVE NOT USED IT FOREVER...EXCEL CONDITION, TRYING TO SELL TO SOMEONE WHO WOULD LIKE IT.

NOTHING WRONG, JUST DON'T NEED IT LAYING AROUND COLLECTING DUST.

THIS BLENDER IS AWESOME!

INTEREST?

I HAVE THIS EXACT BLENDER AND HARDLY USED IT AT ALL EXCEL COND, IT'S BEEN IN MY STORAGE CABINET FOR YEARS..TRYING TO SELL IT...ARE YOU INTERESTED?
I HAVE A PICTURE ON CRAIGSLIST IN THE PHILA AREA.
LET ME KNOW...
[email protected]

I neede a new blade unit for my phillips smoothie maker, I just googeld the model number + spare part and was redirected to the websites! Eventually you fine it!!

I managed to order a spare blade unit via internet
Thanx for the reaction

Yes there is, however unless you are very mechinal incline I won't suggest that you try to replace the defective terminal fuse. This is cause by running your blender continuous. Let me know if you are welling to do the repairs yourself, so that I can give you the directions. Sign, Spurs21

Direct or from eBay https://www.google.com/search?q=Kitchen+Aid+Model+KHB300+hand+held+blender+parts ..

Jimmy LavinderYou are tagging a dormant unanswered post that is 10 years old!The section up at the top is for you to ASK the Original Poster a QUESTION before giving him an ANSWER. You can't get any parts for anything online without an email address and a physical address. These parts are never found in a store. Durabrand is a cheap company of the 'sell and run' variety. There are no spares.https://www.google.com/search?q=durabrand+TSK-9368AP+partsDump it and buy a Vitamix, a company that guarantees spares forever or even a Braun, or Oster that guarantees them for 10 years...

Olabisi. It is better to create your own question rather than tagging a 13 year old question in the area where you ask the OP for further information before committing to an answer. Stir function runs the blades at a much slower speed to incorporate ingredients slowly. https://www.kitchenaid.com/pinch-of-help... STIR. To stir ingredients in a blender, start with a low, slow speed and gradually increase it to a medium speed. Blend until ingredients are completely combined. Different Blender Settings and What They Do - KitchenAid ..

Actually I do repair these stick types all of the time. The trick is getting the head off. Then its a simple Process to remove the shaft and clean inside and add bearings or bushings of needed. After removing the blade and blade holder, Remove the coupling at the top, then remove the 4 screws. After that you will see a aluminum washer. Stop here. To remove the head assembly, you need to make a large slide hammer like a split bearing. Lead or steel is good. Or a circle of cement 8 inches in Diameter and 4 inches thick. The inside hole should be as close to the diameter of the mixer shaft as possible. Cast it in two halves so when assembled it forms a ring around the shaft. Wrap this with lots of duct tape. also place a ring of duct tape around the plastic head where the cement will touch it. now wearing gloves, grab the metal base (or secure it to something with a chain or in the fork of a tree). Once secured, slide the weight quickly against the plastic head assembly. After a few hits the head should pop out. Then remove the shaft, replace the o-rungs in the center bearing, clean the unit & reassemble.Use Silicone as sealant when reassembling the body. There is no need to remove the lower seal assembly but clean it with a small bottle brush. I have included pictures of this procedure but im too ugly to make a You Tube Video. ;) These pictures are from my teaching tool and were cut to show anatomy. Theseafox Enterprises

Question edited for clarity. Question moved from Washing Machines category to Blenders. Something to do with the Outlet and Soy Milk! :>D https://www.amazon.com/gp/customer-reviews/R3S2NMMMKVYCV8?ASIN=B09L7PXN1B https://www.google.com/search?q=joyoung+a+super+power+blender+e08+error ..

Question edited for clarity. That is likely a failed heating element, failed thermostat, or worse case scenario, a failed control board. https://www.google.com/search?q=prolectrix+soup+maker+not+heating+up ..