U-Line Logo

U-Line Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 152 Products
  • 1K Answers
  • 140K Views
0helpful
3answers

U-line CLR2160 won't go into clean cycle. I hold the power button while pressing the light button 3 times.

I had to hold Power for 10+ seconds (until last "F" flashes, quickly let go of Power, then press and hold it again and while holding it pres the light three times.The process doesn't follow the manual's instructions at all. Their older model units with the physical on/off/clean selector switch was much more reliable than their new 2160 with touch screen controls!
10/28/2021 1:17:34 PM • U-Line Icemaker • Answered on Oct 28, 2021
0helpful
2answers

U-line bar refrig/icemaker

The fact that the compressor is two years old does not mean it cannot break down again, give more details on the problem to troubleshoot further
4/15/2021 9:52:49 AM • U-Line... • Answered on Apr 15, 2021
0helpful
1answer

BCM 95. Why is there no condenser fan or compressor activation when turned on?

because it is an automatic machine
3/24/2021 7:33:17 PM • U-Line Icemaker • Answered on Mar 24, 2021
0helpful
1answer

My uline echelon 2175RF shows

Hello, I followed your instructions, hold the up arrow and at the same time press and release the light bulb 3 times and then up arrow to 3, got the Er codes E3 and E5, now I'm trying to do the last step to go back to refrigeration cycle and it doesn't work. Help?
3/21/2021 3:00:56 PM • U-Line Echelon... • Answered on Mar 21, 2021
0helpful
1answer

U-Line Model WCM48

Sorry for the delay in responding...

Most models have the valve located at the back of the machine on the lower left hand side(viewed from the front). You may have to remove the entire back cover via the hex head screws to get at it. (some models have the valve located behind the front toe kick panel.)

First follow the waterline to determine the location of the valve within the fridge. If it is at the front then the toekick panel will have to be removed. If there are no visible screws then it is most likely a clip on style. If there is a knob for temperature setting then the knob may have to be pulled off first.
If there is a smaller cardboard panel at the bottom rear of the fridge remove it and you should see the valve. If not then remove the entire back cover by removing the screws along the rear perimeter of the fridge. The panel may stick to the back of the fridge but gently pull and it will remove. The valve should now be seen and can be disconnected.

Be sure to unplug the machine first and turn off the water supply. There will still be some pressure in the waterline so have a towel ready.

The valve itself is available online, I think the correct one is located at: http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=832567&PPStack=1

Just be sure to verify that it is the right one before ordering.
12/18/2020 4:14:55 PM • U-Line... • Answered on Dec 18, 2020
0helpful
2answers

How to install an icemaker water supply line over concrete floor?

IM USE A 1/4 INCH WATER LINE LOOK FOR A SINK OR WASHER CLOUSE BY AND ATACH TO THE HOT WATER LIND IF YOU HAVE LIME IN YOUR STATE IF NOT USE THE COLD WATER RUNTHE HOSE INSIDE THE CAVINET TO HIDE THE HOSE.
8/30/2020 4:13:19 AM • U-Line Icemaker • Answered on Aug 30, 2020
0helpful
1answer

Need a new ice maker assembly to fit a U-line 45A ice maker. New part is $500 with tax so I Need a cheap alternative I can make work. Has 6 wires running from it.

Check with your local appliance repair shop. They may have what you need out back or know where you find the part you need. They might even have after market parts cheaper.
8/1/2020 11:03:24 PM • U-Line... • Answered on Aug 01, 2020
0helpful
2answers

After a power outage the ice maker stopped

Tell him to first fill ref-regent gas in compressor cause if does not have enough the comp will over heat a cut of .
7/26/2020 4:49:30 AM • U-Line Icemaker • Answered on Jul 26, 2020
0helpful
1answer
0helpful
1answer

I have question it does not say on the know but which was do I turn the knob for it to get colder its a u-line refrigerator uln-75th-00

Put it in the off position. Turn the knob to the right. If the refrigerator comes on then continue to turn the knob to the right until you get to the temperature you want.The more you turn to then right colder it should be. Turning it back makes it warmer.
1/9/2019 12:16:42 AM • U-Line... • Answered on Jan 09, 2019
0helpful
2answers

ULine 1175BEV door has a weak seal, does not close easily.

Use a good level and ensure that the unit is not tilted forward, it should be tilted to the rear slightly. The side to side should be level.
1/2/2019 3:58:10 PM • U-Line 75R... • Answered on Jan 02, 2019
0helpful
1answer

The alert notification is from a u-line refrigerator and beeps even when door fully closed

Since you did not mention what make it is . Its usually dirt in your door seal causing your refridgirator to understand its not closed since its not sealing properly . clean the door seals and try . Or there is a technical glitch in electrical system and you need a repairman . Also there is usually a way to disable the alarm and you need to check your user manual for that to disable it ill its fixed
6/1/2018 4:50:59 AM • U-Line... • Answered on Jun 01, 2018
0helpful
3answers

Uline 75R refridgerator stopped working

Sounds like you did everything right
3/1/2018 4:24:01 PM • U-Line 75R... • Answered on Mar 01, 2018
Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top U-Line Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

ray gallant

Level 3 Expert

73786 Answers

Tom Chichester

Level 3 Expert

62196 Answers

Are you an U-Line Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...