Terk Audio Players & Recorders - Recent Questions, Troubleshooting & Support
Antenna interface - Sirius to XM, Dodge
connector should fit - provided that there is ONLY one connector for the SatRad and not two.
You might have to trim off some yellow, or pink or green plastic, but the metal connector should fit.
2/27/2013 12:25:15 AM •
Terk XM...
•
Answered
on Feb 27, 2013
Ever since XM radio radio
It appears this is an ongoing issue with the XMD1000, dating back to 2006, and the new lineups that XM/Surius is releasing. After the lineup changes, many people report the XMD1000 has issues with the presets and a workaround has not been issued. It appears the frequency is slightly off and the tuner is not hitting on that exact frequency each time. The solution would be to contact Terk/AudioVox, or better yet try to find a retailer that carries the XMD1000 and purchase a new one, place the old one in the box and return it for a refund. This has been most peoples solution to the issue. Let me know if you require additional information or assistance regarding this issue.
Terk XMD 1000 need power coed
You can make one if you have the 4 pin white nylon connector. You only need 3 pins, one to 12volts for memory, one for 12volts accessory radio power, and one for GROUND. Let me know if you have the 4 pine white nylon connector, then I'll get you more info, okay?
My xm plays extremely loud thru my car stereo.no
Are you playing it directly thru your FM antenna connection, or using the RCA jacks? You have to set the FM modulator level. It is also possible that you have a new FM radio with a type of ALC that will raise the lever regardless, but your regular car radio volume control should work. do not wire this directly to a power amp, as you won't have the control that you need. Good luck, let me know more.
8/10/2010 2:38:10 AM •
Terk XM...
•
Answered
on Aug 10, 2010
Could my Terk XM antenna be bad right out of the
Yes, it is possible, but go outside and face the SW and try it that way to make sure. If you have an unplugged or bad antenna, if will usually say "CHECK ANTENNA". Make sure you don't have a chunk of metal, or even your hand over the top of the mini antenna, or you WILL block the signal. Let me know how it works for you. good luck!
8/10/2010 2:35:23 AM •
Terk XM...
•
Answered
on Aug 10, 2010
Why does my xm radio always have to be refreshed
You need to have one wire on an always 'hot' power feed. Be careful, as some GM products have a timer that shuts off the power after a 10 minute timer, so that could be your issue. Are you talking about a factory installed XM, or one like the photo above?
No signal on my xm sony car stereo (on boat with terk marine ant)
the xmd1000 has been having alot of defective units your best bet would be to have yours checked but my first thought would be somethings rong with the xmdson110 check all your wireing make sure none of it has any nicks or brakes in it, if guess that its more likely that the xmdson110 is bad rather then having 2 xmd1000 go bad in a row.
I had a xm portable
Hi it is the Sirius and Xm merger. The channel's being changed are normal. My XM radio did the same thing a month ago.
1/9/2009 8:47:40 AM •
Terk XM...
•
Answered
on Jan 09, 2009
How to disassemble mx5020 speaker?
Greetings,
Please check the handbook of your device to see if there are diagrams highlighting the location of the screws for the speakers. Once located, you can start by using a screwdriver to remove those screws and open up the device. Otherwise, you might need to work with an electrician or possibly a pawnshop to help get the device open. Thank you.
I bought a PSWi-8M wireless
Unfortunately you need the transmitter. i would contact Polk and see if they sell this part separately or start scouring the internet. someone might have blown their sub but the transmitter would still work.
Motorola DCP-501 All-In-One Home Theater Receiver will not come on at all?
Check the power source and if you can get behind the switch, check for continuity. Make sure that the device is properly connected to a power source and that the outlet is functioning. You can test the outlet by plugging in another device.
Check the power cable and make sure that the power cable is properly connected to the unit and the power source. Also, check for any damage or fraying on the cable.
Check the power switch to ensure that the power switch is turned on. It is possible that it might have been turned off accidentally.
Try resetting the device by disconnecting it from the power source, waiting for a few minutes, and then plugging it back in.
If all those fail, you will need to take to an audio engineer.
Not finding what you are looking for?
