Startrac Fitness Products Exercise & Fitness - Answered Questions & Fixed Issues
My Lamar L1400 treadmill stopped working. The
Hi, please open the cover where is motor and controller board motor, and see if there are some loose cable. And if NOT tight very well all connector, and wires with a plier.
and turn ON again. If the machine after that present the same problem, you must replac the Controller board motor.
[email protected]
My horizon treadmill immediately stops after 2 seconds
StarTrac 4500 Treadmill NO RPM Error
Probable Cause
A) Damaged or misaligned RPM sensor
B) Display Cable
C) MCB
D) Filter Network
Corrective Action
A) Check the connection of the RPM sensor to the lower control board. Inspect RPM sensor and disc for build up of dirt, dust, or debris. Clean if necessary. Verify RPM sensor and disc are properly aligned. Units equipped with an "optical" RPM sensor (uses plastic RPM disc) should have the disc evenly spaced between the walls of the RPM sensor. Adjust if necessary. Units equipped with a magnetic "cherry" RPM sensor (uses a metal RPM disc) should have the sensor spaced 1/8" away from the flywheel. Adjust if necessary. B) Inspect the display cable for any nicks or breaks. Replace if necessary. If there is no visible damage to the display cable, wiggle the display cable to verify intermittent connection. If by wiggling the display cable, the PWM LED on the lower control board does not flash or intermittently respond, replace the display cable.
C) Refer to the NO RPM Flowchart from the service manual for MCB testing.
D) Refer to the NO RPM Flowchart from the service manual for testing of Filter Network.
Star Trac 4500 Treadmill NO RPM Error Code
Star trac 4500 display board does not come on
You should first check the power from the wall outlet and then follow the power going into the machine -- once you find the place where the power stops, you will find the problem.
Stairmaster quinton 612 plus error code e201
Quinton Error E201
Probable Cause
Grade Over Limit Fault. Turn jackscrew counter clockwise to get within range.
Corrective Action
- Use Up or Down arrows to bring grade into range.
- If error persists, replace grade actuator or VSD. NOTE: Belt and display may continue to be used during fault conditions by pressing clear.
Quinton Treadmill Error Codes E201
Message ELSTL what does it mean
This means the elevation has stalled. Please see the EL STL Flow Chart in the service manual starting on page 68.
http://www.sportsmith.net/images/product_support%5Cstartrac%5CTechnical%20Manuals%5CTreadmills%5CSvcMan%20TR4500.pdf
Keydown pro star trac treadmill
This means you have a stuck key on your keypad. The solution most of the time is to replace the keypad. You can view this information starting on page 55 of the service manual.
http://www.sportsmith.net/images/product_support%5Cstartrac%5CTechnical%20Manuals%5CTreadmills%5CSvcMan%20TR4500.pdf
My star trac treadmill is reading key dv
I think you mean key dn....This means you have a stuck key on your keypad. See page 55 of the service manual.
http://www.sportsmith.net/images/product_support%5Cstartrac%5CTechnical%20Manuals%5CTreadmills%5CSvcMan%20TR4500.pdf
Star Trac 4500 el r n g
All the error codes can be found in the service manual in section 3.
http://www.sportsmith.net/images/product_support%5Cstartrac%5CTechnical%20Manuals%5CTreadmills%5CSvcMan%20TR4500.pdf
Trac Star 4500 trouble Code EL STL
The error code by definition is listed in section 3 of the service manual.
http://www.sportsmith.net/images/product_support%5Cstartrac%5CTechnical%20Manuals%5CTreadmills%5CSvcMan%20TR4500.pdf
Not finding what you are looking for?