Stanley Proto Measuring Tools & Sensors - Recent Questions, Troubleshooting & Support


replace the battery and if it still doesn't calibrate then junk it

Stanley Proto... | Answered on Apr 30, 2017


I know it's 3 years old this question but I had the same problem. Good thing is the makita battery willl fit. I just got one from ebay works great

1500mAh 7.2V BATTERY FOR MAKITA 7000 7002 7033 192695-4 632002-4 Cordless Drill

Stanley Proto... | Answered on Mar 12, 2016


It is a good laser, but it is self leveling so you will have trouble setting it on the floor and be able to title it. It will probably go into error mode and the laser will flash telling you that it isn't level.

Suggest a step ladder that is about the right height.

Stanley Proto... | Answered on Jul 16, 2011


sorry but we know nothing about them but if it worked before the change you made then put it back where it was

Measuring Tools... | Answered Yesterday


5505E MEASUREMETER BATTERY CHANGE (3V CR-2032)
REMOVE WHEEL AND SHAFT BY GENTLY PULLING AXLE OUT OF UNIT.
DRILL OUT 7 PLASTIC HEADS WITH 3/16 DRILL BIT. (ABOUT 1\8 DEPTH)
SPLIT TWO SIDES OF CASE AND REMOVE HANDLE.
SLIDE OUT CLEAR PLASTIC CONTROL UNIT. PUSH DOWN ON BUTTONS AS YOU REMOVE SO AS NOT TO DAMAGE THEM.
PUSH DOWN SLIGHTLY TOWARD THE CASE ON LOCK TABS WHILE GENTLY PULLING CASE APART. START ON ONE END AND WORK YOUR WAY TO OTHER END. KEEP GASKET INTACT. OPEN CASE.
THERE IS A "Y" SHAPED RETAINER HOLDING IN THE BATTERY. WITH NEEDLE NOSE PLIERS, CAREFULLY SLIGHTLY SQUEEZE THE BOTTOM OF THE "Y" AND PULL UP GENTLY. YOU CAN NOW REMOVE THE BATTERY AND INSTALL THE NEW ONE. PUSH RETAINER DOWN TO LOCK BACK IN.
MAKE SURE GASKET IS IN PLACE AND PUT CASE BACK TOGETHER, MAKING SURE WHEEL ADAPTER IS IN PROPER PLACE. TURN ON AND TEST CONTROL UNIT AND TURN WHEEL ADAPTER TO MAKE SURE UNIT IS WORKING PROPERLY.
SLIDE CONTROL UNIT BACK IN BEING CAREFUL OF THE BUTTONS. RE-ASSEMBLE HANDLE AND PUT THE TWO SIDES OF THE CASE TOGETHER. I USED THREE PIECES OF ELECTRICAL TAPE TO HOLD CASE TOGETHER. ONE ON THE TOP BETWEEN THE TWO HOLES, ONE ON THE BOTTOM JUST ABOVE THE DISPLAY, AND ONE IN THE MIDDLE.
PUT THE PLASTIC PIECE IN THE HOLE AND LINE UP. MAKE SURE BOTH O-RINGS ARE ON THE AXLE SHAFT. GENTLY INSERT AXLE ALL THE WAY IN WHILE ROTATING IF NECESSARY.
I WAS SO HAPPY I HAD IT ALL BACK TOGETHER AND WORKING, I HADN'T TAKEN ANY PICTURES AND I DIDN'T FEEL LIKE TAKING IT ALL APART AGAIN. MIGHT ADD PICTURES LATER IF NEEDED. I HAD BEEN LOOKING FOR YEARS ON HOW TO CHANGE THE BATTERY, AND I FINALLY MADE UP MY MIND THAT I WAS GOING TO DO IT.
JMS 10-20-2020

Measuring Tools... | Answered on Oct 21, 2020


You can try the following: 1# Check the main power cable & make sure it has 110V (Do not run the machine with long extension cable).2# Check all harness connection.3# Check keyboard cable connection on back of control board.4# If all the cable connection is good then you may need to replace the control board.

Measuring Tools... | Answered on Aug 02, 2020


Those are precision devices and require factory check up and calibration at regular intervals. Contact your dealer.

Measuring Tools... | Answered on Aug 01, 2020

Not finding what you are looking for?
Stanley Proto Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Stanley Proto Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

18455 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

59342 Answers

Are you a Stanley Proto Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...