Standard Pool & Spa - Recent Questions, Troubleshooting & Support


manual says error 170 front board sevice indicated and usually caused by low ac voltage from backboard check backboard and transformer voltages if voltages are good a shorted cell will also cause this

Standard Power... | Answered on Jun 02, 2018


called a repair guy to fix. Thanks anyway.

Standard Power... | Answered on Nov 23, 2017


check your jandy valves make sure they are fully open or closed they can lock your system if they are not in full closed or open mode second option is to try to turn jandy valves manually to if they are in spa mode manaully change then to pool mode or if they are in pool mode change them to spa manually on the jandy valve there is a 3 way switch this is where you can turn them manually wt we want is to send the signal back to the main control outside that the valves are in ready mode look in the main control open the door and see if there is a red light that indicates another problem if you can send me where the red light is what the red light label says it will help if you send me the aqualink model #

Standard Power... | Answered on Nov 23, 2017


Try pressing 'TEMP' then 'LIGHT'. You may have to do this a couple of times.

If you don't have a 'TEMP' button, either the temperature up or down will also work.


There are three modes, ECONOMY (EC / ECO / ECON), SLEEP (SL / SLP) and STANDARD (ST / STD). For everyday use keep it on STANDARD mode.

Cheers,
Ian Kime
Ian Kime Hot Tub Sales Repairs and Servicing

Standard Pool &... | Answered on May 04, 2017


check to see if you have proper voltage coming in then test transformer to see if 24 volts if so start unplugging the auxs 1 at a time until it goes away sounds like a relay is stuck if not give me more info

Standard Power... | Answered on Sep 07, 2014


shut off whole system re boot salt sensor will re calibrate

Standard Power... | Answered on Sep 05, 2014


I have worked on RS systems for many years and have not yet run across one that hums. I would think that it may be coming from one of the relays or a light dimmer, if you have one installed. Unless you are well comfortable working with high voltage, call out a tech to isolate the source and determine if any repair is necessary. Sorry I couldn't be of more help.

Standard Power... | Answered on Jan 13, 2013


the outlet you are powering it with is too low in amperage to run the spa or the pump is shorted or seized

Pool & Spa | Answered 3 days ago


possible bad sensor or cell

Pool & Spa | Answered on Feb 28, 2021


Hi. Have a balboa hot tub which keeps going into economy mode, the temperature has stayed at 17 for a week and filtration is on 2 hrs twice a day. It has a mode button. Keep setting the standard setting but then slips back to economy right away. Help

Pool & Spa | Answered on Feb 23, 2021


If this is an outdoor spa near trees, its almost a guarantee that the impeller is blocked with debris (pine needles can cause this in a hurry)

If the impeller is clean of debris and this is still happening, replace you pressure/flow switch.

Pool & Spa | Answered on Feb 21, 2021


From their website
https://snowflamepelletstoves.com/
Our multi-fuel pellet stoves can burn dried wheat, corn or wood pellets. Multi-fuel stoves, unlike just wood pellet stoves, are the first heating option that allows you to burn all three environmentally friendly fuels in the same stove. The Environmental Protection Agency rates multi-fuel stoves as the most energy efficient stoves available.

Pool & Spa | Answered on Feb 20, 2021

Not finding what you are looking for?
Standard Logo

12 questions posted

Ask a Question

Usually answered in minutes!

Top Standard Pool & Spa Experts

john h

Level 3 Expert

23577 Answers

David Spradling
David Spradling

Level 3 Expert

11960 Answers

rogerpaul3

Level 1 Expert

62 Answers

Are you a Standard Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...