Smeg Ovens - Recent Questions, Troubleshooting & Support

0helpful
1answer

How do I replace element in smeg se366ss-5 oven? The element is fitted with one screw at the bottom and 2 bolts welded to the plate.

Yes, the welded bolts you see have a nut on the other side. If you pull the stove out, you should see a cover that you remove for access. Make sure the power is off! https://www.amazon.co.uk/SMEG-OVEN-ELEMENT-2700-806890386/dp/B003010GPK/ref=pd_lpo_1?pd_rd_i=B003010GPK&psc=1 ..
9/16/2021 8:36:07 PM • Smeg Ovens • Answered on Sep 16, 2021
0helpful
1answer

SMEG C30GGXU1 Gas oven getting too hot

Then it sound slike your thermostat is not work . you coiuld try cleaning burner or injectore first . but I would say thermostat
8/29/2021 9:24:50 PM • Smeg Ovens • Answered on Aug 29, 2021
0helpful
1answer

Model spa42016. Why doesn't oven heat?

Oven comes on and off intermittently or heats very little: If the timer feature is activating and you have not touched the timer button at all, this would have to be a failed Electronic Oven Control. The timer button is either shorting at times or closing on its own from heat or moisture. The Electronic Oven Control would need to be replaced to repair the problem. Or Why does it take the oven so long to bake? When the food is taking way too long to bake, it's probably a weak bake ignitor. Replacing the ignitor usually fixes this problem, but you probably want to verify that the ignitor is the problem before replacing it. Sometimes the oven thermostat or oven sensor can be calibrated wrong, or it may be faulty. If your particular range has an oven that uses an electronic thermostat, and the oven temperature is off by tens of degrees, you probably have to replace it. On most units that have a mechanical thermostat, you can actually remove the thermostat knob, and adjust the knob to more accurately represent the actual setting of the thermostat. On many models, there's a screw on the back of the knob with a small calibration plate or ring. You can loosen this screw and adjust the calibration plate. Remember to tighten the screw again. If yours isn't adjustable, and the temperature is off by a large amount, you should just replace the thermostat. Or Oven safety valve needs to be checked with multi meter ohms / voltage ALSO Test the Burner Heating Element The stove's burner heating element is a coil of metal sheathed in an insulator. Electrical current travels through the element. Resistance to the passing of electrical current causes the element to heat up. A precise temperature cannot be set for a burner, instead it is turned on and off repeatedly by the control to the achieve an average temperature. When it is set to a low temperature, the element is cycled on and off more frequently. For high temperatures, the heating element is energized longer with fewer on and off cycles. Some burners have two elements, with the second only being used only for high heat settings. Before testing the heating element, unplug the appliance or shut off the power at thefuseboxorbreaker panelto avoid an electrical shock hazard. When a burner does not heat at all, or only heats up to a lower than expected temperature, the problem is likely to be with the heating element, the temperature control switch, or the wiring. If it only heats at the highest temperature, the problem is with the control or an electrical short, not the burner. If the burner works only intermittently, the problem is likely in the wiring or connectors. To test the heating element, try the following steps. First, disconnect the heating element from the stovetop. In most cases, this is done by lifting up the burner on the side opposite of the terminals (the part of the burner that disappears under the stovetop). Remove the decorative ring. Inspect the style of connection. If the burner element has visible blades that fit into the receptacle block, pinch the block with one hand, and pull the heating element free with your other hand. If the terminal block clamps over the element, the housing must be removed and the burner wires disconnected. Unsnap the metal piece or remove the screw that secures the receptacle block and then disconnect the element. Inspect the heating element. If you find bubbles, warping, or damage to the insulation sheath, the burner must be replaced. If the terminals are dirty or corroded, this can cause poor temperature control, intermittent problems or complete failure to heat. Clean the terminals with steel wool or very fine sand paper to restore good conductivity. Test theresistanceof the heating element using amulti meter. Set the multi meter to the ohms setting X1 and touch one probe to each of the terminals. A normal reading is typically somewhere between 20 and 120 ohms. The exact reading differs by manufacturer and mode. If the meter reads infinite resistance or the other extreme of the scale, zero resistance, then the element is damaged and should be replaced. If the measured resistance differs significantly from the expected range, the element is probably bad, but if possible, determine from the manufacturer what the actual resistance should be. To test for a grounded or shorted element, touch one probe to the surface of the burner and the other probe to each terminal in turn. If you get continuity at any time, the heating element is defective and should be replaced. The reason for my free advice is GOD is good! element burner 0-undefined-undefined-0_1.jpg ignitor connectia_04-undefined-undefined-2_0.jpg element oven ceramic burners-undefined-undefined-5.jpg element burner testing range element-short.2-undefined-undefined-9_0.gif
8/21/2021 9:01:30 AM • Smeg Ovens • Answered on Aug 21, 2021
0helpful
1answer

Smeg Double Oven SD08

this can be hard to do as you should have locked the hinges with the door fully opened before taking it off. the hard part now is (with the door off) you have to push the spring loaded hinges down and lock them with small hook located on each hinge once locked the door will go back on the oven. you then open the door fully and unlock the hinges, good luck
8/17/2021 2:37:11 PM • Smeg DO81CSS... • Answered on Aug 17, 2021
0helpful
1answer

Is my SMEG SA360X-5 oven dead?

everything is repairable depends on is it worth it --thats is an answer for you as to oven get an estimate and compare repair vs replacement
7/28/2021 8:20:51 AM • Smeg Ovens • Answered on Jul 28, 2021
0helpful
1answer

SMEG SA708X oven's symbols have rubbed off, wioul

Here's a picture of the panel... BTW does anyone know the wiring / have a wiring diagram for the door switch as mine was swapped around by an oven guy just to get it running but now I have a new switch and can't remember how it all goes!!
5/30/2021 10:31:27 AM • Smeg S1100MFX5... • Answered on May 30, 2021
0helpful
1answer

Oven does not work on defy 831

Where is the capillary on a defy 831.
5/6/2021 9:48:26 AM • Smeg SE250XUK... • Answered on May 06, 2021
0helpful
1answer

Smeg oven buzzing sound

I have same problem.
2/23/2021 1:51:41 PM • Smeg Ovens • Answered on Feb 23, 2021
0helpful
1answer

Help! I have a Smeg oven Model Number: SA410X-5. All of the symbols have come off. I have just moved in to a new place with this oven and have no idea what the symbols are meant to be! Im urgent need of help!

https://stoveconnection.com.au/shop/index.php/brand/smeg/sticker-sets.html/p063737285-1.html.htmlI found the decal set for this oven and also the oven instructions to match each decal
2/9/2021 9:28:13 AM • Smeg Ovens • Answered on Feb 09, 2021
0helpful
1answer

SMEG S340GX oven's symbols have rubbed off, would appreciate a clear photo of the front panel

This is the only site that shows an image, but not big enough to read. http://www.manhein.com/home/print.php?produit=fours&num=S340GX&categorie=gc6&marque=Smeg Contact them direct, they may do a replacement sticker set. https://www.smeg.com/contacts ..
2/7/2021 9:26:54 PM • Smeg Ovens • Answered on Feb 07, 2021
0helpful
1answer

Model sfpa7395x2. Why Has display failed?

Failure of the display or its control board
11/16/2020 8:22:25 PM • Smeg Ovens • Answered on Nov 16, 2020
0helpful
1answer

Smeg Oven SA360X oven won't heat but fan is on and thermostat indicator lamp is on and the grill works ok too. What could be the problem please.

faulty element usually situated behind back panel circlling the fan
12/8/2019 8:58:28 PM • Smeg Ovens • Answered on Dec 08, 2019
0helpful
2answers

Smeg oven diplaying an "A" in display

I have had the same problem today - trying to change to day light saving time - can you help me too if you find out.
7/17/2019 6:29:17 AM • Smeg SE399X/5... • Answered on Jul 17, 2019
0answers
0helpful
1answer

I need a picture of the oven dial for smeg 60 and 90 cm wide electric ocen

Picture of oven dial for smeg 60 cm wide electric oven is: 60 cm-iy1avqwe2pkwjqqdjf13t0if-4-0.jpg Picture of oven dial for smeg 90 cm wide electric oven is: 90 cm-iy1avqwe2pkwjqqdjf13t0if-4-2.jpg
4/11/2019 1:59:24 PM • Smeg Ovens • Answered on Apr 11, 2019
Not finding what you are looking for?
Smeg Logo

712 questions posted

Ask a Question

Usually answered in minutes!

Top Smeg Ovens Experts

Paul Bade

Level 3 Expert

1688 Answers

Dennis Boxerman

Level 3 Expert

1306 Answers

The Knight
The Knight

Level 3 Expert

76823 Answers

Are you a Smeg Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...