Sharper Image Air Purifiers - Recent Questions, Troubleshooting & Support

0helpful
1answer

Unit will sometimes make a crackling noise.

Mine does it too, I finally just tried something else when I was cleaning the blades. I took some alcohol on a qtip and with the blades out of the machine I wiped up and down the line wires that are inside that go from the top to the bottom, and also the little balls that are on the bottom of the wires that slide when you turn your unit upside down. It seems to work, I do it every time I clean the blades. scribner062
11/11/2022 7:03:54 PM • Sharper Image... • Answered on Nov 11, 2022
0helpful
1answer

I have a Sharper Image Deluxe Fire Fan Model #FZ25-50A2 that is making noise, how do I clean it?

Hi, please attempt to use a qtip and/or a tissue to clean any dust out of the fan. I would also use the table of contents within the manual of the device in order to get any cleaning advice from the manufacturer.
7/26/2022 11:12:13 PM • Sharper Image... • Answered on Jul 26, 2022
0helpful
4answers

Ionic breeze is arcing inside unit

I have a sharper image ionic breeze hybrid gp that ran fine for years unitl it recently started sparking / arcing at the base of the grid blades and always in the same spot. I cleaned it several times but the sparking always came back and the unit went into either "drying grid" or "attention required" mode. The solution I found was to stand the removable grid in 2 inches of Pine-Sol cleaner 50/50 diluted with water for 24 hours then brush again with the cleaning brush and hot water. Presto! No more sparking.
5/16/2021 5:50:43 PM • Sharper Image... • Answered on May 16, 2021
0helpful
2answers

How to get replacement parts for Sharper Image ionizer?

one of the electrodes broke off the botto of one of my towers.
2/28/2021 4:42:30 AM • Sharper Image... • Answered on Feb 28, 2021
0helpful
1answer

Sharper image wont turn on unless plugged in

no kidding???
11/16/2020 11:14:10 PM • Sharper Image... • Answered on Nov 16, 2020
0helpful
12answers

Ionic breeze 3.0 repair

My Ionic Breeze GP began losing power occasionally but I could shake it and get it to turn back on. It got worse and worse until it would not turn on anymore.

The problem on mine is the micro switch that detects whether the collector plates are inserted or not, so it is part of the safety mechanism. There is a about a one-inch cylindrical piece of plastic on the front of the collector plate handle. This cylinder goes through a hole and pushes on the micro switch (actually a plastic cover over the micro switch).

On mine, it appears that arcing inside the switch caused it to get hot, deforming the plastic a little bit and apparently ruining the inside of the switch.

The following URLs describe the switch, but I have not found a retailer that carries it:
http://www.dicgroup.com/pdf/SM/SM5-01N.pdf
http://www.dicgroup.com/e-pro01-sm.html

Another of the same model switch is used in the back of the unit to detect whether the rear cover is on (over the UV bulb).

If I cannot find a replacement, I am thinking of either bypassing the bad switch entirely or swapping the switch from the back. Either way would defeat a safety feature so it's probably not to be recommended, but I consider the sacrificing the switch for the back cover to be introducing only limited risk, so I might take that route if I have to.
11/2/2020 4:10:59 PM • Sharper Image... • Answered on Nov 02, 2020
0helpful
1answer

Need instructions on how to replace batteries on a Sharper Image Model No MI 215 BBQ Fork

download instruction manual https://www.manualslib.com/manual/903369/Sharper-Image-Mi220.html
5/19/2020 7:17:39 PM • Sharper Image... • Answered on May 19, 2020
0helpful
2answers

Who repairs the sharper image ionic breeze GP

This is a repair that someone I know didafter reading a post on the net.....regarding Quadra repairs....and here is a link for repairs....its all one link....so type it into your browser or paste it.....

http://www.airpurifierrepair.com/ProductDetails.aspx?ID=34&ProductId=591


Remove the grid assembly.

Remove the 4 screws holding the top on.

Gently remove the top as there are wires connected to it.

Once removed, find the microswitch assembly on the side. There will be 2 green wires going to this assy board (PCB).

Examine the bottom of this board. On both my units, the PCB wascorroded badly on the trace that runs from the center lead to the wireconnection. This will cause the microswitch to quit working.

What I did was soldered a wire from the center contact of themicroswitch (center piece coming through the board. There should be alarge solder pool) to the wire connection at the edge of the board.This just 'goes around' the corroded PCB trace.

Worked fantastic on both ionic breezes and took about 5 minutes for thesecond one. The first one took over 2 hours just to find the problem.

I hope this helps.....good luck...thanks for rating my effort....the Fang.
7/14/2019 4:57:40 AM • Sharper Image... • Answered on Jul 14, 2019
0helpful
1answer

I'm looking for a manual for The Sharper image electrostatic air cleaner model#. EVSI-XSOI

Ask google with make and model
4/11/2019 10:20:13 AM • Sharper Image... • Answered on Apr 11, 2019
0helpful
1answer

How do I obtain a manual for the sharper image ultrasonic wave cleaner - SI411

Try this site. I FOUND THIS WEB SITE that I think will help you with this question and a lot more. Since this web site will have access to many different vehicles I hope you do not feel like I am lazy by just passing along the web site instead of giving you the exact information you asked for. Go to this site to find a manual to help you. https://www.browsemanuals.co/lander_zrk65_test14.html?t1=1535071160&t2=65192170713&t3=kwd-28425796&gclid=EAIaIQobChMI-oybpN624AIVwdVkCh2GtguWEAEYASAAEgJ9yvD_BwE
2/23/2019 12:18:56 AM • Sharper Image... • Answered on Feb 23, 2019
0helpful
1answer
0helpful
1answer

My grandson bought a sharper image streaming video drone 4 days ago with his own money. This drone will not lift off under full power. Would like money back or new drone that works.

Contact Vendor for refund or replacement under warranty. FIXYA doesn't sell anything. Regards.
8/27/2018 10:31:18 PM • Sharper Image... • Answered on Aug 27, 2018
0helpful
2answers

My wife wanted me to take it apart to clean it

You can replace the fuse by soldering a new one into place -- it's a standard fuse, just match the amp rating of old to new.

Chances are though, after you do this, it will blow again. So, there's a good chance the unit is kaput.

I have extensive experience with these units to the point of even replacing the high-voltage field wires (the two fine wires which run from top to bottom) with titanium wire. There is no real good way to keep these things running properly -- they're kinda like weed whackers -- inherently problematic.
7/6/2018 1:28:38 PM • Sharper Image... • Answered on Jul 06, 2018
Not finding what you are looking for?
Sharper Image Logo

727 questions posted

Ask a Question

Usually answered in minutes!

Top Sharper Image Air Purifiers Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

David Shaub

Level 3 Expert

2994 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22509 Answers

Are you a Sharper Image Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...