Sharp Aquos - Recent Questions, Troubleshooting & Support
There are two green lights
The tv main logic board known as a tv Tuner signal board it is the causes and the problems.The tv main logic board,the tv Tuner signal board it is shorted and not taking in and sustance power from the tv power supply board anymore that why tv Power and OPC LED lights indication are flashing together.This main logic tv Tuner signal board that the board where that take in the tv incomming broadcasting signal wire plug into it.U must replaced the main logic tv Tuner signal bard to fixed this problems.If U have some mechanicals skills like take things aparts and putting it back together again?Yes,tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish main logic tv Tuner signal board for the replacement.Tries tv unplug,replug it back about an hour later.Tv might work again for awhile though,but to fixed this problems for good the main logic tv Tuner signal board must have to be replace.
32
i had the same problem in a sharp tv 32". on the remote control there was a view mode button, i changed the mode and the pc input label in the left upper corner gone
Why doesn't it turn on?
Might be a problem with its Power Supply Regulator Board [SMPS] inside.
If you wish to get some details; check the sites linked here.
https://elektrotricks.blogspot.com/
https://electronicshelponline.blogspot.com/
Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault. Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in by Webview with mobile or by desktop. Mobile View has no search box. Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.
10/24/2021 1:36:35 PM •
Sharp LC...
•
Answered
on Oct 24, 2021
Lcd sharp tv flashing green light
Try unplugging the unit and while unit is unplugged hold the volume up button and channel down buttons down and while depressing both buttons plug the unit in. Let go of the buttons and the unit should come on in the service mode. There will be a small k on the screen. With the sharp remote press the channel up button once. This should bring up a menu that will show a lamp error line. If the lamp error is = to 5 the unit is in lamp error shut down. User channel down to highlight that line and curser right arrow to highlight the lamp error #. Hit the enter button to clear the lamp errors. Now unplug the unit and let it sit for a minute and plug back in. I hope this corrects the problem. If the unit does not come on by doing this or if it does and you do not find lamp errors the power supply pcb may have been damaged by the surge.
Sharp LC 60LE640U will not turn on power light just blinks
Those blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "
brand name" to your device, in the "
Search box at the top right of the display window of the Homepage" to get gathered related posts.
The tv menu keeps popping up
Hello,
The reason your television keeps popping up the menu is simply because, either the remote or the televisions menu button is stuck.
To test if it is the remote, remove the battery from the back of the remote and try to operate the television from the buttons on the television to see if it works, if it pops up, then it means the problem is not from the remote and its from the television.
Either ways you have to open the remote and clean the panel with naphthalene, then adjust the menu button on it. or you can as well get a new remote for your television if you cannot clean it on your own.
Also to fix the television if it is detected as the fault, get the appropriate screwdriver, open up the television, then try to locate the menu button, then you adjust it and try to operate with either the remote of the menu key on the television.
Once it is seen to be working, ensure that the television is properly coupled back.
Always make sure the keys on the coputer and the television are not pressed too hard.
Take care
Not finding what you are looking for?