Sears Building Materials - Page 9 - Answered Questions & Fixed Issues
1045 manual
learn button is on the back of the opener it should be a square orange button.
Why is my garage door suddenly reversing when going down?
Deb, that reversal is a child safety device - if the bottom edge of the door detects contact with any object, it'll immediately reverse so it doesn't kill a child. Or a cat, dog, whatever.
The opener mechanism should have a stop switch that prevents the door from closing hard against the floor - that stop switch needs to be adjusted so that the door will stop JUST before hard contact. That'll take care of it "bouncing" off the floor & reversing. As to it reversing before it touches the floor... examine both guide rails closely to see if there's any obstruction that the door's bottom edge may be contacting to trigger the child protection reversal switch.
What could be the problem with garage door opener?
Many openers have a short length of wire that serves as a primitive antenna; ensure the wire is hanging free.
The remote is a radio frequency transmitter, the other end in the garage has a tuned receiver.
Either one of these can drift from their original operating frequency which then can cause the system to fail.
Most modern openers are encoded so that they can resist operating with CBs and amateur radio signals and most require a one-time operation that allows the inside receiver to recognize (and remember) its dedicated remote by its frequency and the unique code the remote produces.
While this principle makes openers more secure, it also allows for more failures of the type you are having.
Take a look at the manuals available at the following site to see is there is one close enough to your model number to let you restore the programming between remote and receiver:
Free Craftsman Garage Door Opener User Manuals ManualsOnline com
The garage door has power
clicking can be an overheated motor from trying to much. other idea is troley opened too far and lodged against bolt on rail by motor.
My keypad worked just fine but the battery died and I replaced it. All the lights on the key pad work but I can't seem to reprogram it. I press the learn button enter the code press and hold enter th
Sometimes theres a tiny reset button hidden in the batt area. Are you positive that the new batt is fully charged silly Question but Iv\'e gotten burned on special size batts its like the sit on shelf and no body cycles their stock...Im assuming the manual is nowhere to be found? Almost is like I had a remote to a blue ray that was acting crazy turns out one of the buttons was being pushed constantly and not letting any other logic take its place have you ever changed batt before? what happens if you putt old batt back in? What does it take on your end to "reprogram" it? this odd of results may require a phone call or a downloaded manual from the internet. How did you know to enter the learn mode? is there a users manual but not a trouble shooting manual? Ive heard that powering it up and entering the model # directly after auto prog\'s logic also some times holding 1 and enter or 1,0, and power// or 1and power. hope at minimum I gave you a few options (damn this digital world!!! ) good luck friend let us know outcome...S
Chamberlain troubleshooting
Check to see if sensors (eye) on sides of door are lined up, they need to be looking directly at each other. If that doesn't work change sensors, simple, install, hook up 2 wires per sensor, wire with line to same wire, blank wire to same blank wire and align so sensors see each other. If you need further help, reach me via phone at
https://www.6ya.com/expert/frankie_091f536560a54e12
Genie H4000A manual
The garage door will only go down by holding the button on the wall switch
7/20/2014 10:13:28 PM •
Sears Genie...
•
Answered
on Jul 20, 2014
•
1,082 views
How do I replace sears side light bulb on door opener
To replace the bulb you have to remove the plastic cover which is held on with tabs and one or two sheet metal screws (usually on the top of the unit). The bulb is in a standard light socket. It is best to replace it with a bulb that resists vibration such as a ceiling fan bulb.
How to replace the lift capaciter on a chmaberlain garage door opener
Most capacitors are just behind the outer cover. Remove the cover you will see the capacitor (looks like a D cell battery with terminals). Be careful not to get a shock, they store power. using insulated needle nose pliers pull off the connectors. Take a phicture with your phone before removing the wires. Put the same wires back in the same place and secure the Capacitor with the clamp you loosened to remove it. Your motor will now be able to "start" from the current jolt it needs...................
How do you loosen the belt on a LiftMaster garage opener?
Get a 1/2in open ended wrench. On the left hand side of the belt (if you face the door), there is a small spring. At the end of the small spring there is a square nut. Loosen that nut by turning counter clockwise. This will loosen the belt.
Can I buy a new remote for 41A435-7
Ebay.
http://www.ebay.com/sch/i.html?_odkw=41A435-7+remote&_osacat=0&_from=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.TRS0&_nkw=Sears+Craftsman+LiftMaster+Chamberlain+Garage+Door+Opener+Wireless+Keypad+Model+976LM+Security%2B&_sacat=0
What does the purple button light flashing on 1/2 horsepower craftsman garage door opener
I think the adjustment mode is on.
For example, that's from Craftsman manual:
""
Setting the Force
The force setting button is located on the left panel of the motor unit. The force setting measures the amount of force required to open and close the door.
1. Locate the purple button on the left panel of the motor unit (Figure 1).
2. Push the purple button twice to enter the opener into Force Adjustment Mode (Figure 2). The LED (Indicator Light)
will flash quickly.
3. Push the remote control or control console (Figure 3). The door will travel to the DOWN (close) position.
""
Actually, you should just read carefully your garage door opener unit's manual.
Craftsman Garage Door Opener Remote
Not finding what you are looking for?