Scubapro Scuba Diving & Snorkeling - Answered Questions & Fixed Issues

Call scuba pro they can assist you with problem if they can not fix it over the phone send it to them for repair or replacement.

Scubapro Subgear... | Answered on Apr 08, 2017 | 2,198 views

They sell aftermarket mouth pieces that you warm in water once soft and pliable you bite down it takes shape to your bite plate which is further back in your mouth and can not be pulled out .

Scubapro... | Answered on May 16, 2014 | 345 views

Denx7d could have not said it any better i have about 1300 dives on my gear and still in good shape and have annual service on my gear now i am a certified repair technician for scuba pro these regulators they sell are the best on the market hands down

Scubapro... | Answered on May 16, 2014 | 301 views

Oral inflate bcd and place in water watch for bubbles if in bladder send it back to scuba pro for repairs dump valves have seals that can be replaced

Scubapro Scuba... | Answered on May 16, 2014 | 260 views

balanced regulators make noise on initial pressurization

Scubapro... | Answered on May 16, 2014 | 453 views

these are controlled by scubapro due to they need specail testing equipment to repair regulators E..G now IP pressure is 135 psi and there is no adjusting screw shims and springs then the cracking effort test to see if you have pressure flutter or creep. these can not be seen with out testing equipment.

Scubapro Scuba... | Answered on May 16, 2014 | 397 views

the spg hose has a oriface in it so that if the hose burst you do not lose all your air underwater at once. have your scuba shop test it for proper operation.

Scubapro... | Answered on May 16, 2014 | 308 views

the whistle noise is some thing loose (torn o-ring) inside the second stage. this is covered under warranty. scuba pro offers a parts for life program which is no cost to you if 1st & 2nd stage with a computer are bought at one time. just pay service labor. the whistle noise will be repaired are replaced free under 1 year.

Scubapro Mk25 &... | Answered on May 16, 2014 | 343 views

I have a smartcom very nice dive computer this issue can ONLY be repaired by scubapro themselves the smartcom is obsolete they will give you trade dollars toward a galleo or luna which are better dive computers

Scubapro UWATEC... | Answered on May 16, 2014 | 546 views

Scuba pro has repair facilities everywhere they can fix this problem with a annual service kit.

Scubapro... | Answered on May 16, 2014 | 313 views

To rebuilt a first stage regulator requires special tools a quailfied service technician should rebuilt it put in a o-ring in the wrong spot can be fatal at deep depths you can call scuba pro direct and they can assist you in finding a repair facility close to you are they can repair it .

Scubapro MK11... | Answered on May 16, 2014 | 738 views

I use a Cressi reg no problems

Scubapro Full... | Answered on Sep 19, 2011 | 325 views

thay change all the seals weather there bad or not thay do it for safety reasons

Scubapro... | Answered on Apr 24, 2011 | 176 views

thay clean and change the o-ring the needly seat and new diaphram its some thing that you do every year to certifi for ins. purposes

Scubapro... | Answered on Apr 24, 2011 | 181 views

You should be able to pop the computer out of the rubber housing (it will be tight) the details will be on the back. Hope that helps.

Scubapro Uwatec... | Answered on Nov 05, 2010 | 441 views

You will need to contact your nearest Scubapro authorised dealer. You can look up your nearest dealer from the main scubapro website. Most Scuba shops that undestake servicing will be able to sort this for you as scubapro is a worldwide brand.

Scubapro MK2... | Answered on Nov 05, 2010 | 211 views

yes thats all you have to do, just make sure the lock ring is in place correctly. good luck and have a great holiday.

Scubapro Scuba... | Answered on Nov 04, 2010 | 281 views

Any Scubapro dealer. Usually at least one in any major town or city.

Scubapro Twin... | Answered on Aug 19, 2010 | 320 views

Check here:

May not have exactly your model, but something very very similar. Also, keep in mind, the second stage will free-flow as an "overpressure safety" if the first stage is malfunctioning. Check your intermediate pressure (should be ~150). If you can't do this, try your second stage on another first stage (any brand), and try another second stage on your first.

If it is for sure your second stage, check for proper adjustment of demand lever, bent/damaged demand lever or diaphragm plate, or damaged valve seat.

Scubapro Service... | Answered on Jun 27, 2010 | 404 views

check here:

Scubapro MK2... | Answered on Jun 27, 2010 | 326 views

Not finding what you are looking for?
Scubapro Logo

Ask a Question

Usually answered in minutes!

Top Scubapro Scuba Diving & Snorkeling Experts

Bill Boyd

Level 3 Expert

53816 Answers

ray gallant

Level 3 Expert

70776 Answers

Tom Chichester

Level 3 Expert

60200 Answers

Are you a Scubapro Scuba Diving and Snorkeling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides