Scotsman Freezers - Recent Questions, Troubleshooting & Support

Check with an appliance parts supplier for suggested replacements.

https://www.manualslib.com/manual/1095484/Samsung-Rf195abrs.html?page=94#manual I checked this wiring diagram and could not see any sensor that would control the fans. there are many units that will keep the fans off till a certain temp is reached so as to not circulate warm air after a defrost. you may have a bad sensor?

perhaps it's unhappy? I can't say i blame it, if I had to sit there all day in the freezing cold making ice I would moan too. here's a list of possible problems If it makes excessive noise:- Problem and Likely Causes/ Probable Solutions Fan blade vibrates Blade is bent Replace fan blade Fan motor mount is broken Replace motor mount Compressor vibrates Mounting loose Check mounting Water pump vibrates Pump bearings worn Replace pump Panels vibrate Mounting screws loose Tighten screws and ice can groan as it expands, but that only applies to large icebergs

Ice thickness probe disconnected or faulty.

you can look to see if the rubber door seal is being pinched or is deformed, if so you can pour boiling water slowly on the seal all over and when its all hot close the door and let it cool in the right position...

Hi

Please check the water inlet valve, it might be frozen or blocked with mineral deposit. Use a hair dryer to remove the blockage. Make sure the water inlet valve's screen is not blocked. If the issue persists, then the water inlet valve has gone bad, use a multimeter to test the water inlet valve's continuity. Use a multimeter to test the continuity. If that is fine then test the auger motor and replace if bad. Hope this helps...please post back for further assistance.

Daniel

This is the only distributor in South Africa:

Website contact page:
http://www.icesystems.co.za/index.php?page=contact

SCOTSMAN SA (Pty) Ltd - Ice Systems (Pty) Ltd

Postal Address : p.o.box 44 - Riverclub 2149

Physical Address : Lakeview Business Park
Unit 4,8 - 10 Yaldwyn Road
Jetpark, Boksburg
phone : +27 10 590 0609
phone : +27 87 720 0245/6/7/8
fax +27 11 826 4123
fax +27 86 634 0803

Mr. Rob Wooler
[email protected]
[email protected]

There are other Distributors in Africa listed here:
http://www.scotsman-ice.it/distributors.asp?id=af
This is the best I can do with known product Scotsman support sites. There may be others but... I would stick with the company supported distributor for your Model FR620LTV-X thermostat needs.

Thanks for choosing FixYa,

Kelly

http://www.scotsman-ice.com/docs/uploaded/sct/manual/Csw45m.pdf
start with this site as it has your machines manual with trouble shooting section.

they have a web site you can go to

Might be some ice build up blocking something. Why not move the frozen good out of the way and grab a hair dryer for a quick thaw in the area of question. It can't hurt anything. Please be kind with a Thumbs up for me effort, Raz

The power required for the compressor can be provided either directly by a motor or indirectly by a belt or a gear drive. In these compressors, cylinder clearance volume, compression ratio, amount of suction superheat, valve pressure drops, and the refrigerant-oil characteristics are the main parameters which affect their efficiencies.
so get the motor checked it may be weak and so the diagnostic light shows: Low temperature discharge.
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

This is usually an indication that the photo eyes are probably dirty. They "See" across the opening where the ice drops through. If they are dirty, it registers as a fill machine.
A bin stat can cause the same problem.
The eyes and sometimes be a major problem finding them getting to them. On smaller machines like this one, it's hard to get your hands on them.
Good Luck and hope this helps.

i would check the manifold for mineral build up. this could be the issue for the unstable water flow.