Samsung CLP - Recent Questions, Troubleshooting & Support - Page 6

have u tried universal print driver, available at the Samsung website

You can check the level of each item.
1. In ready mode press the Menu button on the control panel everal times until you see 'Setup 'on the bottom line
of the display.
2 Press the Enter button to access the menu.
3 Press the scroll button until 'Maintenance ' displays on the bottom line.
4 Press the Enter button
5 When 'Check Others ' displays on the bottom line,,press the Enter button .
6 Press the scroll button until the item you want to check displays on the bottom line.
7 Press the Enter button The display shows the percentage of item.
8. Press the scroll button display either 'Image Count' or 'Reset'
9a. Choose 'Reset' and press enter to reset the counter after replacing a consumable item
or
9b Choose Image count to display the counter.
10. Press the Upper Level button to return to step 7 and select a different choice or press it a second time to return to step
6 and choose a different item.
11. To return to the Ready condition press the Upper Level button several times until 'Ready' appears in the display.

samsung clp color leserjet printer writes this massage toner exhaust yellow toner. i have done the toner refil without the reset chips about two times now and i have been printing for some time now i get the message "toner exhaust yellow toner"

No toner reset procedure , u need to replace toner chips ,else replace with oem toner cartrdiges

clean lsu ,

• Most likely there is a scratch on drum of imaging unit
• or scratch or dust on transfer belt
• or dust on LSU

Check all these , should get resolved.

dear
pl. run the application "samsung easy printer manager" and check the meaning of error.
model of the printer is meaningful.
t hanks.

clean the contacts or replace the cartridges that are lighting up

d/l utilities drivers

Open the front of the printer, and you will see the four toner drums; cyan, magenta, yellow and black. Immediately to the left of the cyan drum there is an "L" shaped drawer : That's the waste toner drawer. It pulls straight out. If you enjoy driving around and spending money, you can buy a new one. If you are frugal and practical empty it as follows: To do this cleanly I recommend wearing a pair of latex gloves! At the top of the container there is a square opening with gray foam on the inside edges - this is where the toner can be dumped out. Take an empty bread or bagel bag and put it over the end of the cartridge far enough to cover that square hole plus another inch. Gather the end of the bag and secure it with a rubber band or tape making sure the hole of the cartridge is INSIDE but not taped shut, and the bag's edges are properly sealed. Now you can turn the cartridge upside down and agitate it in different positions until all the toner is dumped into the bag. Flick the bag with your fingers to let the toner fall to the bottom, them put around the bag to keep all the toner at the bottom, and carefully remove the tape or elastic. Using a lightly moistened paper towel clean up the cartridge and reinsert it into the printer. Now if you haven't left too much air in the bag gently take the end with all the toner in your palm, gather the rest of the bad with it into a small ball in your fist and pull your glove off over the whole lot. take that in your other hand and remove that glove. Voila! The cleanest toner dumping ever!

For me it was an issue with the print queue. Clear all jobs and/or create a new queue and try again

bad chip on toner cartridge.

It might need a drum replacement or a fuser replacement.

there is no print head in this model is a laser printer with drum 1-check toner level and the setting of toner density in setup. 2-remove toner cartridge and clean entire printer with air blower 3-replace toner cartridge

contact with your dealer. imaging unit life is over.

sensor is a clip type device, which is situated below the pick up roller.

firstly restart the printer, if same error is comimg. then, fuser error. replace fuser unit

I'm stepping out on a limb, but I bet it will be the Main Motor. samsungparts.com