Samsung Dishwashers - Page 2 - Recent Questions, Troubleshooting & Support

Mine make a grinding noise also when the wash cycle starts. I had a repair guy over fixing my fridge and he said it was the washer motor. My machine has only been in use for 1-2 yrs. Other owners say that the tabs on the top rack break off and get lodged in the machine. hope this helps a little.

Samsung DMR77LHS... | Answered on Aug 28, 2019

Had a look in the user manual for your dishwasher.

Page 26 shows blinking Heavy light means there is leakage in the dishwasher. Most likely there is water in the base under the drain sump which could cause the flood switch to trip. Turn mains power to dishwasher off. Pull it out from under kitchen bench without breaking the hoses. Put some towels on the floor and turn dishwasher back and forth on incline to get water out. Wait a little and turn on. If no difference then you need to dry the base and find the source of the leak. More likely the door seal.

Samsung... | Answered on Aug 21, 2019

The arm may be damaged or defective.

Samsung... | Answered on Aug 15, 2019

The Normal, Heavy and Smart lights will blink when there is low water level in the dishwasher. Check that the sump area isn't blocked from filling with water. Often there is a float inside the tub that can be held down by a utensil that fell under the lower basket. Remove any foreign objects. Then try to run the dishwasher when it is completely empty. The parts diagram for the dishwasher is available here: . If there isn't an obvious blockage in the water level monitors, you could have a wiring problem or an issue with the control board that doesn't get the signal for water reaching the desired level. (Note: if the incoming water pressure were too low, only the Smart light would flash.)

The manual for the DW7933LRABB is available from Sears Parts Direct on the product page: . The current link to the manual is .

I hope this helps.

Cindy Wells

Samsung... | Answered on Aug 05, 2019

I get 4e error code just on the delicate cycle and It does not go to cold.

Samsung... | Answered on Jul 06, 2019

Dishwasher Door Gasket Replacement - Samsung ...

? 1:18
Feb 11, 2015 - Uploaded by
Dishwasher Door Gasket Replacement - Samsung Dishwasher Repair (part ... Dishwasher Lower Door Gasket (part #WD08X10075) - How To

Samsung... | Answered on Jul 02, 2019

Okay, maybe it's the spelling that's a problem. Try Case Brake Assembly, or Brake Case assembly. The part number (for your dishwasher) is DD94-01005A. It's available from for about $54. You may also need the Case Sensor, part # DD94-01006A for about $44, but I would start with just the Case-Brake Assembly first. 90% of the time, that part alone will fix your problem.

If you need further help, reach me via phone at

Samsung... | Answered on Jun 26, 2019

Check bottom pan for water flood switch located there so it’s trying to pump water out check for leak cause or if you are opening door to add dishes while it’s alrea started this could cause water leak dripping down into pan

Samsung... | Answered on Jun 17, 2019

Just look on the words written fuse to your dishwasher

Samsung... | Answered on Jun 16, 2019

There is no internal fuse that I am aware of, if it will not run then more then likely the control panel is defective.

Samsung... | Answered on Jun 07, 2019

Could pump or controller failure

Samsung... | Answered on Jun 01, 2019

It’s probably trying to pump water out from dripping pan if you have water leak will activate drain pump by it self turn off water supply and electric maybe need to be pulled out to see if any water on bottom

Samsung... | Answered on Apr 24, 2019

Not finding what you are looking for?
Samsung Logo

1,349 questions posted

Ask a Question

Usually answered in minutes!

Top Samsung Dishwashers Experts

Cindy Wells

Level 3 Expert

6101 Answers


Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18342 Answers

Are you a Samsung Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides