Russell Hobbs Recent Questions, Troubleshooting Help & Support

Possible similar model free manual online: https://manualzz.com/doc/7183663/rhdw14ss---russell-hobbs

Question edited for clarity. Question moved from Misc category. Duplicated question deleted. Refresh page to see question. Looks like the first link, although no model given. https://www.google.com/search?q=Russell+Hobbs+Uno+Uno+Pod+coffee+machine. ..

I had the same problem which I managed to solve. The electro magnet that holds the toast lever down takes its power from a poor joint.
Remove the bottom of the toaster. You will see 2 wires encased in a heat proof sleeving going from the small circuit board. One of these wires dissapears up inside the heating element board about mid way along the board. You will now have to remove the metal covering by twisting 6 tabs. This is best done by taking off the black knobs you use to push the toast down - if you can - I couldnt, so I had to use long nosed pliers to bend the tabs and then with difficulty, remove the metal cover. YOu should now see the terminal that the wire is connected to. It is this connection that fails either between the wire and coonnector or connector and heatin element on the reverse side. I put a small bolt through the hole and used a nut to tighten the pressed fitting. I didnt use solder because I thought that it would just melt!
Anyway, my toaster worked after that. Russell Hobbs failed to give me any advice at all.
I hope that has helped.
Neville
Welwyn Herts

See is the videos here help. https://www.google.com/search?q=russell+hobbs+express+steam+iron+wiring+diagram&rlz=1C1QJDB_enCA643CA644&sxsrf=APq-WBuHt2lHpbuE5nsjrZh-8itNx6N-7w:1646764053732&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjV6M2Tkrf2AhUVCc0KHX2cAMoQ_AUoAXoECAEQAw&cshid=1646764119190708&biw=1920&bih=937&dpr=1 And here as well. The wiring is generic, power, thermostat, heater. https://www.google.com/search?q=steam+iron+wiring+diagram ..

Read the operator's instructions. They are available of the Russell Hobbs site or by contacting Russell Hobbs UK on-line through the "Contact" link. In most cases, steam irons tend to clog with hard water deposits and need to be de-scaled from time to time. If that doesn't help you, buy a new iron. Rowenta's seem to perform best.

When on iron iron get heated up the tank also heated up but water is not being sucked my machine from water compartment no voice or sound is heard to pump in water to make steam

It appears that most parts are obsolete. You may have to just grow flowers in it as a keepsake. https://www.google.com/search?q=Russell+Hobbs+Kettle+model+3100%2F1%2F2+parts This was sooo promising

Russell Hobbs Obsolete Switch Assy Stat 3100/1/2 Kettle

BuySpares https://www.buyspares.com > kettle > product > shop=... Buy Russell Hobbs Obsolete Switch Assy Stat 3100/1/2 Kettle online from BuySpares. Specialist supplier of Russell Hobbs Kettle Spares, Parts & Accessories. ..

It makes cold soups like Gazpacho and Vichyssoise, so make sure the heating / cooking function is set. If it is, ask Russel Hobbs where your local service centre is to diagnose and replace the element. https://www.google.com/search?q=Russell+Hobbs+soup+maker ..

personally i would quit using it, does not sound safe, but it is your home.

This error code is usually related to door or door lock problems. To fix this problem, you can do the following: 1. Door check: Make sure the washing machine door is closed properly. If the door is open, close it and try to start the program again. 2. Resetting the washing machine: If closing the door alone does not solve the problem, you may need to reset the machine. To do this, press and hold the Quick Start button for 5 seconds to reset. Then try starting the program again. 3. Check the door lock: Make sure the door lock is working properly and replace it if necessary.

Maybe this will help; To deactivate the Child Lock, both the rapid wash and easy ironing auxiliary functions should be pressed at the same time for 3 seconds.

Question edited for clarity. Question moved from Russell Hobbs Washing Machines. an appliance repairer would look at it for you unless you wish to try yourself. Mine has 4 screws underneath to get access to the motor. The issue in normally that the carbon brushes on the motor either wear out or stick. If the electronics for the timer have failed, it is unlikely that you can get parts, but worth a try. https://www.google.com/search?q=russell+hobbs+rhmx1+hand+mixer+repair ..

You were replying to a Chinese AI Answer Bot. I am currently deleting all the wildly generic answers. Try and claim on the warranty. The circular studs on the front are the way into it, but then you have to find spares. Toasters are deemed disposable appliances. https://www.amazon.co.uk/Russell-Hobbs-14356-2-Slice-Toaster/dp/B002AMVYTC/ref=cm_cr_arp_d_pdt_img_top?ie=UTF8 ..

check cartridge is positioned, aligned, and secured in place correctly. It could cause leaking if it is not placed correctly.

I would say not normal. Presumably it stops when you unplug it? On standby it should be silent. Contact the maker.

If your Russell Hobbs 19001 appliance does not turn on even after replacing the fuse, there could be a few potential causes for this issue. Here are some troubleshooting steps you can take:

1. Check the power source: Ensure that the appliance is properly connected to a working power outlet. Try plugging in another device to verify if the outlet is functioning correctly. If possible, try using a different power cord to eliminate the possibility of a faulty cord.
2. Inspect the power switch: Examine the power switch on the appliance for any visible damage or issues. Make sure the switch is in the "on" position and not stuck or loose. If you notice any problems with the switch, it may need to be repaired or replaced by contacting the manufacturer or an authorized service center.
3. Reset or check for a safety feature: Some appliances have built-in safety features that may cause them to stop working under certain conditions, such as overheating. Check if your Russell Hobbs 19001 has a reset button or an automatic safety shut-off feature. Follow the instructions in the user manual to reset or troubleshoot these features.
4. Contact customer support: If none of the above steps resolve the issue, it is recommended to contact Russell Hobbs customer support or an authorized service center for further assistance. Provide them with details about the problem and any troubleshooting steps you have already taken. They may be able to offer additional guidance or suggest further troubleshooting or repairs.

If the cleaning solution is not coming out of your Russell Hobbs RHCC5001 Carpet Washer, there are a few potential causes for this issue: 1. Check the Solution Tank: Ensure that the solution tank is properly filled with cleaning solution. Sometimes, the solution may not dispense if the tank is empty or the level is too low. Check the tank's fill level and refill it if necessary. 2. Unblock the Solution Path: It's possible that the solution path or nozzle may be clogged or blocked. Carefully inspect the solution dispenser nozzle and any associated tubes or hoses for any obstructions. Use a small brush or pin to remove any debris or buildup that may be blocking the flow of the cleaning solution. 3. Prime the Pump: If the carpet washer has been unused for a while or if the cleaning solution has dried up in the system, it may be necessary to prime the pump. Fill the solution tank with warm water and let the carpet washer run for a few moments to allow the water to flow through the system. This can help clear any blockages and prime the pump for proper operation. Once the water flows through smoothly, empty the tank and refill it with the cleaning solution. 4. Check the Spray Settings: Ensure that the carpet washer's spray settings are adjusted correctly. Some models have adjustable spray settings, such as low, medium, or high pressure. Make sure the spray setting is appropriate for the cleaning task you're performing. 5. Clean or Replace the Spray Nozzle: If the spray nozzle itself is clogged or damaged, it may need cleaning or replacement. Refer to the user manual or contact the manufacturer for specific instructions on how to clean or replace the spray nozzle on your Russell Hobbs carpet washer. If you have attempted these troubleshooting steps and the issue persists, it is recommended to reach out to Russell Hobbs customer support or their authorized service center for further assistance. They should be able to provide you with more specific guidance based on the model and help you resolve the problem.

Manuals on the Russell Hobbs website is country dependent. https://www.google.com/search?q=Russell+Hobbs+Cafe+Continental+Model+3344+manual ..

1. Unplug the coffee grinder from the power source and ensure that it is completely cool.
2. Look for the screw or bolt that is recessed into the base of the coffee grinder. It may be covered by a rubber pad or sticker. Remove the pad or sticker to expose the screw.
3. Use a screwdriver to remove the screw or bolt from the base of the coffee grinder. Make sure to keep the screw in a safe place so that you do not lose it.
4. Gently lift the top of the coffee grinder off the base. You may need to use a bit of force to separate the two parts, but be careful not to damage any of the internal components.
5. Once the top is removed, you should be able to access the internal components of the coffee grinder. If you need to remove any other parts, such as the blades, consult the user manual for instructions.

As for the type of screw used in the base, it is likely to be a small machine screw or bolt. You may need to use a small screwdriver or hex key to remove it. If you are unsure what type of screw to use, you can take the screw to a hardware store and ask for assistance in finding a replacement.

I descaled my kettle because it needed to be done (it was quiet before I descaled). However, it has become noisy since I descaled. Any suggestions, most welcome?