RTO Logo

RTO Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 1K Products
  • 20K Answers
  • 592K Views

I have the same gun, and had the same problem. Turns out the solution is the plastic airline between the gun and the paint cup (or in my case, the small hole in the upper fitting that this hose connects to). In this sprayer, because it isn't gravity feed, there is pressurized air fed from the gun into the paint cup. That pushes the paint from the cup into the gun. In other higher pressure systems that use a paint cup, the venturi pull of the air is sufficient to get the paint up the feed tube from the bottom of the cup and into the gun, but this gun specs a max air pressure of 10 PSI. In my case, I got a small amount of paint into the drip tube above the cup, and when it dried I had a clog there. To verify, pull the plastic hose from the top of your gun and also remove the paint cup. If you can't blow air through that tube, you won't be able to get any paint to the gun.

RTO Central... | Answered on Jul 15, 2020


If you send the model number I can give you a specific part number, but the issue is the head switch is stuck on.
This can be caused by a bad switch or the cylinder not returning entirely.

RTO PasLode... | Answered on Jun 30, 2020


If you wiah to get some details about treadmill error codes and solutions then check the following link
http://electro-medical.blogspot.com/

RTO Sole F80... | Answered on Jun 30, 2020


you might have to clean the firing pin, it may be covered with powder residue..

RTO Paslode... | Answered on Jun 15, 2020


on 2006 freightliner century with 12.7 detroit 60 Error code
eng contreller no resp. 128s254 07.

RTO Ho Herpa... | Answered on Jun 11, 2020


hai , check communication cable, speed sensor

RTO Sole F80... | Answered on Feb 23, 2020


Running lights don't work and headlight don't come on?

RTO Gas Motor... | Answered on Jan 07, 2020


A check engine light and fault 61 code is an electrical failure to the injector or a bad solenoid on the injector, but you will most likely find your problem at the terminal crimp.

RTO Ho Herpa... | Answered on Jan 07, 2020


There are several places you can go on the web that have free atv repair/owners manuals. The owners manuals usually have a wiring schematic on or towards the last page also trouble shooting diagrams with instruction in them.

Type in your search bar: atv polaris (year) model:trailblazer/500cc.
If you like email: [email protected] with specs and I will email it to you.

Hope this was helpful
Try2B8me

RTO 200cc Full... | Answered on Dec 24, 2019


Maybe you can ask your supplier, in generally, they have the wiring diagram for westek 6503BC 150W 3-level.
If you need to purchase a new diesel generator set, please see at www.dieselgeneratortech.com

RTO Westek... | Answered on Dec 03, 2019


I found the manual quite confusing when it came to programming the timer, it might be counter-intuitive but the instructions on YouTube, although they might be in a foreign language, were a lot more helpful. Just pick the one with the best visuals.

RTO Intermatic... | Answered on Nov 30, 2019


Sometimes you need to adjust your clutch cable. as the disks wear out you have to tighten it to get it to disengage. if the cable is adjusted too tight then it will slip because it is not taking all the pressure off the disks so they can fully grab. That is where i would start

RTO 200cc Full... | Answered on Nov 16, 2019


No idea, it can be varible

RTO Toys | Answered on Nov 11, 2019


not all the boot cd´s is working on the old computers, now I do not know how old your computer is, but you can try to contact iolo here and tell them about the problem : http://www.iolo.com/ look under support

Hope thats helps :O)

RTO IOLO... | Answered on Oct 21, 2019


Hi,

Here is a tip that I wrote about the Paslode nailers and the problems that can come up with them.

I also have a link to the Paslode manuals which contain Paslode cleaning and troubleshooting guides.

If you need parts for your Paslode, there also is a link for a site that sells the Paslode nailer parts.

Paslode Cordless Nailer Problems



heatman101


RTO PasLode... | Answered on Sep 18, 2019


Replacement Paslode IM350 Cordless Drill Battery
  • Type: Ni-MH
  • Volt: 6V
  • Capacity: 3000mAh
  • Color: Black
  • Weight: 309.25g
  • Dimension: 134.60 x49.40 x28.10mm
http://www.drillbattery.com.au/buybattery.php/paslode_IM350_power+tool+battery.html


85c0b7d9-ad2b-435e-b473-5f083dc99e92.jpg

RTO PasLode... | Answered on Sep 14, 2019


You can paint it with reguslar paint as lomg as you clean it real good and ruff it up with sandpaper. You will have to spray primer on it first before painting it. I hope this helps. Don't forget to rate this answer.

RTO How To Paint... | Answered on Jul 10, 2019


I have a 2010 freightliner with the code:f8fcff - spn: 523512 FMI: 31

RTO Ho Herpa... | Answered on Jun 21, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top RTO Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Bill Boyd

Level 3 Expert

53814 Answers

ray gallant

Level 3 Expert

68557 Answers

Are you a RTO Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...