Roland Computers & Internet - Answered Questions & Fixed Issues

0helpful
2answers

Boss RC-3 does not power on

Most likely the device has been incorrectly powered. The most easy way to check this is the following:- unscrew the 4 screws on the RC-3 bottom - slide the board out from the connectors holes- gently detach all the connectors and wires coming to the board- locate the schottky diode (SS14) close to the power input connector- check if the diode is short- replace the diode if it is- if this does not solve the problem probably also the capacitors in the power section are shorted.Message me for further info
1/28/2021 3:50:38 PM • Roland Boss RC-3... • Answered on Jan 28, 2021 • 1,223 views
0helpful
1answer

I had to reset my computer and now PT wont work when I click on the icon it says parameter incorrect can you help please I purchased the prog. on the 07 07 20 thank you Roland

What is PT? You will probably have to reinstal the programme is windows based or use a full backup from when it worked OK.
1/2/2021 5:04:40 PM • Roland Computers... • Answered on Jan 02, 2021 • 23 views
0helpful
1answer

Can i use roland E-500 floppy disk in roland E-600 for beats ?

why not ask them the maker this is computer repair forum. why not post to music keyboard forums.
1/26/2020 6:41:32 PM • Roland Computers... • Answered on Jan 26, 2020 • 47 views
0helpful
1answer

Roland em 20. Power on but no sound

Unfortunately, there are to many reasons to count as to why this might be the case. http://midimanuals.com/manuals/roland/em-20/owners_manual/em-20_om.pdf might help if you don't have it
12/15/2017 6:51:21 PM • Roland Computers... • Answered on Dec 15, 2017 • 193 views
0helpful
1answer

Boss rc 3

It seems that when you engage the recording mode, the RC 3 draws too much power and resets itself. Does it work on battery power? If so, then I'd check the power connector for good fit and for corrosion, and I'd check the adapter for proper voltage, polarity and current. Do you have a "PSA series" AC adapter? If not, then check the fine print on the adapter you have for Output, and make sure it's 9V and also that it says 100mA or higher. The Boss PSA can output 500mA and can usually drive 5-6 pedals with the right breakout cable. And I suppose you already have this, but just in case you want to RTFM: Boss RC-3 Manual.pdf 8-)
12/3/2017 6:08:32 PM • Roland Computers... • Answered on Dec 03, 2017 • 105 views
0helpful
2answers

Roland GR-1 Guitar Synth output volume is VERY low !

change your speaker
6/26/2017 5:20:46 PM • Roland Gr-1... • Answered on Jun 26, 2017 • 1,142 views
0helpful
2answers

How do I tell the software to print my design using the engraver?

check for the power cable or re install the software
8/13/2016 3:46:05 PM • Roland EGX-20... • Answered on Aug 13, 2016 • 137 views
0helpful
1answer

ROLAND 2480 RECIEVE ERROR MESSAGE SUB SYSTEM NOT RESPONSE

This means the low-level part of the operating system is corrupted or missing. Simply try reloading the OS by putting the CD into the CD drive. If it does not allow an OS reload or if it fails, most likely the flash ROM which holds the basic part of the OS has been zapped and will require service. You can also try to replace the internal button battery inside that retains the memory.
3/13/2015 12:30:24 PM • Roland Vs-2480... • Answered on Mar 13, 2015 • 321 views
0helpful
1answer

I have a Roland vs 840 ex it has had a c.f. drive installed the machine seems to work perfect except when I set up and get ready to record and depress play or rec it says no disk. It has a 4gb c.f. ca

Try to initialise (format) it in your computer. Use an external card reader. I think you should use FAT 16 or FAT 32. But once the Roland sees the card, do an initialise there. It could be the Roland can;t work with memory cards above 2 Gbyte, for that try to make a 1 Gbyte partition in your computer and again try if it works.
2/16/2015 12:33:08 PM • Roland Vs-840... • Answered on Feb 16, 2015 • 419 views
0helpful
1answer

Br-80 output jack problem

You need to put jack with matching colour jack .
1/28/2015 10:14:45 AM • Roland Boss Br80... • Answered on Jan 28, 2015 • 118 views
0helpful
1answer

Load a PNY USB Flash card to my TD-11 module?

Try formatting the flash drive. Terry
1/18/2015 5:25:35 AM • Roland TD-11... • Answered on Jan 18, 2015 • 127 views
0helpful
1answer

I am unable to set MX90 as a printer. It is not shown me the option when I go to Roland MetanzaStudio menu -set up the printer- Please help

I found this online....hope it helps... ========================== How do I get computer to recognize printer? You have a problem. Your computer does not recognize the printer. Moreover, you cannot reinstall the printer driver or software because you have misplaced the CD. Well, don't worry. The steps given below will help you out. STEP 1: Checking the Cable and Power Supply The simplest step comes first. Just check whether the printer cable is connected to the computer securely. Moreover, also check whether the printer power cord has been plugged in properly. STEP 2: Uninstall Old Printer Software, If any If you have had an older printer, then make sure that printer drivers and software are uninstalled from the computer. If you don't, the computer might not recognize the new printer. This problem is common in inkjet printers. STEP 3: The Paper Size A simple matter like the incorrect selection of paper might also lead to this problem. If the printer paper size does not match the size set in the printer settings, than the computer might not recognize the printer. STEP 4: Restart There are times when all it requires is to restart the computer. This is in case where you have connected the printer after loading the driver. If this is the case, then just restart your computer. STEP 5: No Pass through Device This is actually an extension of your first step. Make sure that the printer cable has a direct connection to the computer. No pass through devices must be used for this purpose. This Article is written by John C Arkin.
12/13/2014 7:41:32 PM • Roland Metaza... • Answered on Dec 13, 2014 • 84 views
0helpful
1answer
0helpful
1answer

No video is played back on the Roland VR-5? only audio

Try reading the instructions again. I am assuming you have other videos that play.
6/18/2014 9:27:59 PM • Roland VR-5 AV... • Answered on Jun 18, 2014 • 59 views
0helpful
1answer

Fr-1x broket strap fixing

Please, read the following page: http://www.tervis.fidisk.fi/Roland/Modifications
4/30/2014 1:46:37 PM • Roland FR-1X-BK... • Answered on Apr 30, 2014 • 60 views
0helpful
1answer

Terrible sound when transferring unto pc

What software program , do you use on PC to play back , check its settings, in or under Audio
3/6/2014 9:52:36 PM • Roland Boss RC-3... • Answered on Mar 06, 2014 • 99 views
0helpful
1answer

Metaza wont turn off

is it on and can't be turned off? or is it off and can't be turned on?
2/2/2014 6:37:58 AM • Roland Metaza... • Answered on Feb 02, 2014 • 59 views
Not finding what you are looking for?
Roland Logo

Ask a Question

Usually answered in minutes!

Top Roland Computers & Internet Experts

ADMIN Canada
ADMIN Canada

Level 3 Expert

41715 Answers

Gil Shultz

Level 3 Expert

3462 Answers

ray gallant

Level 3 Expert

73786 Answers

Are you a Roland Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...