Rockford Fosgate Car Audio & Video - Recent Questions, Troubleshooting & Support

0helpful
1answer

Where is the fuse located

The 40A fuse should be immediately to the right of the B+ terminal. If you bought this amp used, and it's never turned on before, it's possible the previous owner removed the fuse. It's hard to miss if it's actually there, so you're probably seeing an empty slot where the fuse is supposed to be. With the radio turned off, insert a 40A ATC (blade style) fuse into the slot, and then power it up. x575p3001-o-ykmusyf2kqgtaeqfjmlbejj2-3-0.jpeg If you need further help, I’m available over the phone at https://www.6ya.com/expert/reginald_bec291de192ca44f
11/14/2023 8:15:58 PM • Rockford Fosgate... • Answered on Nov 14, 2023
0helpful
2answers
0helpful
1answer

Rockford Fosgate Punch P1000X5 5-channel car amplifier keeps blowing the in-line fuse?

Internal or external short. Disconnect everything but power, does it still blow? If it does, you need to take it in for repair..
4/20/2023 4:56:49 AM • Rockford Fosgate... • Answered on Apr 20, 2023
0helpful
2answers

2 12 p3d212 2 ohm hooking up to a rockford

Hello a_brake11,

The P325.1 is relatively small to power a pair of P3's. You'll only get 325 watts RMS at 2 ohms (162.5 watts per sub). The P3's power range is from 100-500 watts, so they will work, but don't expect them to be really loud.

For best power, your subs should be wired with the voice coils in series and then the 2 subs paralleled to the amp resulting in a 2 ohm load.

Hope this helps.
1/4/2023 8:20:32 AM • Rockford Fosgate... • Answered on Jan 04, 2023
0helpful
2answers

Amp fuses blowing and amp overheat

Does the amp heat up if you power it up with no speaker wires connected to the amplifier's speaker terminals?
12/19/2022 2:25:47 AM • Rockford Fosgate... • Answered on Dec 19, 2022
0helpful
2answers

Subwoofers are working but aren't that loud.. help me!

not a bad set-up at all. i can help you i do need some more info though. what head unit do you have? what type of box is it just the normal rectangle box with or without divide sealed or is it ported? measure the size of the box and give me the dimensions please? how did you run the cables and how did you hook up between the deck and the amp? does the amp have built in crossover this could be problem just a little tuning? if it does make sure you selelct lpf mode and turn the hz knob all the way down ( counterclockwise) check the gain control should be another knob turn it clockwise all the way. you might need a little flat screwdriver to reach all these. is this amp bridgeable and if so are you running bridge mode ( 1 channel) if not look where you hook up the speaker and look and both channels and you will see a pos connect on 1 channel and neg connect on the other, put both neg wires on neg terminal and put both pos wires on pos terminal. in this set-up you will have full raw power. let me know about this and i will help you the most i can. good luck and happy booming.
8/9/2021 7:42:28 AM • Rockford Fosgate... • Answered on Aug 09, 2021
0helpful
2answers

Remove & replace 100 amp battery fuse

There is a special tool that you can use for pulling fuses but mmost people dont have it because it would not be used that much to justify the costs.
2/15/2020 6:06:38 PM • Rockford Fosgate... • Answered on Feb 15, 2020
0helpful
1answer

I have a Rockford Fosgate 1500 BD amplifier and terminals for the power cable will not loosen or tighten how do I fix it

First off will the fastener turn ? If not try using a bit of wd-40 and letting it "soak" for a little while . Also be sure you are using a good proper sized Phillips screwdriver . If the fastener still won't turn try using a can of "computer duster " inverted so the liquid comes out , note this will be well below zero degrees , and freeze the screw head , then try turning . If the fastener is stripped and the ttol slips you will have to remove the amp cover and grip it with a pair of vise grips ,pliers or a flat blade screw driver .
9/24/2019 1:31:53 AM • Rockford Fosgate... • Answered on Sep 24, 2019
0helpful
1answer

My Rockford fosgate amp power light flashs red when volume is turned up

You may not have enough ground connection or your are running too much power for your amp
6/12/2019 8:53:47 PM • Rockford Fosgate... • Answered on Jun 12, 2019
0helpful
2answers

Can I run 2 12 inch 2ohm fosgate and a 4 ohm 12 on a rockford fosgate 401s 1200 watt amp

Yes. Wire the two 2 Ohm speakers in series and connect them to one channel. Connect the 4 Ohm speaker into the other channel. This will give you a balanced 4 Ohm load on each channel.
5/12/2019 5:55:03 PM • Rockford Fosgate... • Answered on May 12, 2019
0helpful
2answers

Rockford fosgate punch 45 hd mosfet wiring

i have a punch 45 but i'm missing the speaker wire connector.... were do i go to get one...
2/3/2019 9:15:30 PM • Rockford Fosgate... • Answered on Feb 03, 2019
0helpful
1answer

Im looking for a wiring schematuc for the rockford fosgate Punch 40 slider can anyone gelp please?

Please be more specific. RF doesn’t share schematics
2/3/2019 8:58:29 PM • Rockford Fosgate... • Answered on Feb 03, 2019
0helpful
1answer

I need the diagram for the Rockford Fosgate Punch 301m amp.

IF you are looking for a schematic diagram on the amp, you wont find it. IF you need the connection information you can look on their site, There is a repair video on that unit attached . Rockford Fosgate Car Stereo Amp Repair
1/13/2019 4:51:40 PM • Rockford Fosgate... • Answered on Jan 13, 2019
Not finding what you are looking for?
Rockford Fosgate Logo

1,257 questions posted

Ask a Question

Usually answered in minutes!

Top Rockford Fosgate Car Audio & Video Experts

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8992 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Rockford Fosgate Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...