Ricoh IS - Recent Questions, Troubleshooting & Support - Page 8
Door open error shows, even if it is closed
There is a black sensor that detects when the door is closed, and an actuator that the sensor either sees or doesn't see. If this sensor is dirty, it might not be seeing the actuator. It could also be broken or knocked out of place.
SC230
this is an error for the transfer belt there is a mark or the belt has been damaged if you open up th efront cover and then look at the brown panel there are two screws either end that nee to be loosened then lift this up next there is two screws on the transfer unit that run diagonally acros the inside of the machine and a third screw on the black unit (duplex) unit this needs to be taken out.. once you have done this there is a green lever in the top left hand side of the transfer unit this needs to be turned to the left to release the roller take the black duplex unit out by sliding it to the fron then the treansfer unit can be pulled gently out.. it is on two runners so it wont fall off you can hten look at the condition of the belt. if it seems ok look on the edges of the belt by gently turning the gear at the back this will feed the belt around.. if it seems ok put it all back in and then put the srews back in close it up and turn on the machine.. wait for it to warm up.. press the yellow clear/cancel button at the top above the number pad then enter 107 then hold down the cnacel/stop button, hold this down till the screen changes.. turn off the machine and bcak on again.. if the reset has worked the machine should run up and be able to copy and print.. if not you will have to do the same proceedure of clear/cancel button routine and once the screen changes select copy sp then go to section 5.mode then scroll down to 810 sc reset. execute and turn off the machine.. wait 5 secs turn on and test again.. if the error code keeps coming back the B.I.C.U Board may be defective and need to be replaced. check the transfer unit condition of the rollers under the plastic clear image belt also.. Good luck A.
How to repair controller board of Ricoh MP3010?
Repairing the controller board of a Ricoh MP3010 requires knowledge and experience in electronics repair. Here are some general steps to help you get started:
- Identify the issue: Before attempting any repairs, you need to identify the issue with the controller board. This can be done by observing any visible physical damage, checking for loose connections, or running diagnostics.
- Gather necessary tools and equipment: You will need tools such as a screwdriver, multimeter, soldering iron, and replacement components (if necessary).
- Remove the controller board: Remove the controller board from the printer, taking care to avoid damaging any of the components or cables.
- Inspect the board: Inspect the board for any physical damage, such as burned or broken components, and check for any loose connections.
- Test the components: Use a multimeter to test the various components on the board, such as capacitors, resistors, and diodes. Replace any components that are faulty.
- Soldering: If you find any damaged components, you may need to desolder and replace them. Use a soldering iron to carefully remove the old component and replace it with a new one.
- Reassemble and test: Once you have repaired or replaced any faulty components, reassemble the controller board and test it to ensure it's working correctly.
Note: It's essential to exercise caution when repairing electronics, and if you're not confident in your abilities, it's best to seek professional help. Additionally, if your printer is still under warranty, attempting any repairs may void the warranty.
Error 501, 502, 503 & SC441
Error codes 501, 502, and 503 on a Ricoh MP-8001 indicate a problem with the paper cassettes. SC441 is a drum motor error code. Here are some steps you can take to troubleshoot these issues:
- Check the paper cassettes: Make sure that the paper cassettes are properly loaded and that the paper is not jammed. Check that the paper guides are set correctly for the paper size.
- Reset the paper cassettes: Open the paper cassettes, remove the paper, and then close the cassettes again. This may reset the paper cassette sensors.
- Check the drum motor: SC441 is a drum motor error code. This may indicate a problem with the drum motor or the drum unit itself. Check the drum unit and make sure that it is properly installed.
- Check the front door sensor: If the front door open sign is appearing on the screen even though the door is closed, there may be a problem with the front door sensor. Check the sensor and make sure that it is properly installed and functioning correctly.
If these steps do not resolve the issue, it may be best to contact a qualified technician for further assistance. They will have the expertise and equipment necessary to diagnose and repair the problem.
My ricoh aficio sp 100su printer has hardly printed 500 pages and now it show E7 and doesn't print. what must I do?
The E7 error on your Ricoh Aficio SP 100SU printer indicates a paper jam in the fusing unit. Here are some steps you can take to try to resolve the issue:
- Turn off the printer and unplug it from the power source.
- Open the printer cover and remove any paper that may be stuck inside the printer, paying particular attention to the fusing unit, which is located at the back of the printer.
- Check the fusing unit for any damaged or worn parts, such as the fuser rollers, and replace them if necessary.
- Reassemble the printer and turn it on again.
- Try printing a test page to see if the issue has been resolved.
If the error persists, there may be a more serious issue with the printer that requires professional assistance. In this case, you may need to contact Ricoh customer service or a qualified technician to diagnose and repair the problem.
To prevent paper jams in the future, make sure to use high-quality paper that is appropriate for your printer, keep the printer clean and free of debris, and avoid overloading the paper tray. It's also a good idea to follow the manufacturer's recommended maintenance schedule and replace any worn or damaged parts promptly.
Fix colors adjustments after factory reset in printer ricoh spc262
To fix color adjustments on a Ricoh SP C262 printer after a factory reset, follow these steps:
Open the printer driver and go to the "Maintenance" tab.
Click on the "Adjust Color" button.
Follow the prompts in the wizard to adjust the color settings for your printer. This may include adjusting the color balance, gamma, and other settings.
Click "Apply" to save your changes.
Print a test page to see if the color adjustments have been successful.
If the color adjustments are still not satisfactory after following these steps, you may need to calibrate the printer. To do this, follow these additional steps:
Open the printer driver and go to the "Maintenance" tab.
Click on the "Calibrate" button.
Follow the prompts in the wizard to calibrate the printer. This may include printing a test page and adjusting the settings based on the results.
Click "Apply" to save your changes.
Print a test page to see if the color adjustments have been successful.
If you are still having issues with color adjustments on your Ricoh SP C262 printer, you may need to consult the printer manual or contact Ricoh customer support for further assistance.
My ricoh mp 4054 is saying replace fusing belt unit.please call for service now.. what can i do manually to reset it
If your Ricoh MP 4054 is displaying an error message indicating that the fusing belt unit needs to be replaced, you will likely need to replace the fusing belt unit in order to clear the error message and restore normal operation. This is a complex and technical process that generally requires the assistance of a qualified service technician.
Attempting to manually reset the fusing belt unit error message may not be possible or safe, as it may cause further damage to the printer or create a safety hazard. It is recommended that you contact a Ricoh service technician to properly diagnose and repair the issue.
When you contact Ricoh or a Ricoh-authorized service provider, be sure to provide them with the error message you are seeing and any other relevant information, such as the printer's model number and any recent changes or problems you have experienced. This will help them to quickly and accurately diagnose the issue and provide the necessary repairs or replacements.
Not finding what you are looking for?