Remington Logo

Remington Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 512 Products
  • 9K Answers
  • 414K Views

There is a hidden screw just above the charge jack that holds the top cover in place. Remove the plastic plug that hides the screw, unscrew the screw, and pry off the cover. My unit would not charge anymore. I think the charging electronics are poorly designed. I extracted the battery and electronics leaving only the motor, then wired the motor directly up to a 5 volt battery pack. It now works great!
1_21_2012_8_04_15_pm.jpg

Remington... | Answered on Apr 20, 2020


Remington Pole Saw Carbon Brushes
If you're Remington Pole Saw is slowing down, throwing sparks, or not starting you may need to replace the carbon brushes. Replacing brushes and cleaning commutator early can prevent damage to motor armature!
Remington carbon brushes on E-bay Search for:
Remington Pole Saw 8 AMP Carbon Brush

Remington... | Answered on Feb 08, 2020


check for a roll pin in the gear or shaft that has sheared off
check that the square end of the drive shaft is not rounded off or that the square drive in the gear is in fact locking on the drive shaft and not turning from worn out

Remington... | Answered on Dec 28, 2019


Google (remington)(hgx-1)(manual) without parens for instructions OR contact Remington directly to request.

Remington Health... | Answered on Dec 28, 2019


Not sure why you posted this in a health forum, but see this manual for how the spring fits.
https://www.remington.com/sites/default/files/documents/e6206rem_Q7.pdf

Remington Health... | Answered on Dec 04, 2019


Have someone tried bulk ammo deals with free shipping at Ammo Board?
https://www.ammoboard.com/

Remington Garden | Answered on Nov 04, 2019


Contact Remington directly to inquire.

Remington Optics | Answered on Oct 29, 2019


Here is a helpful video that will show you how.
https://www.youtube.com/watch?v=2eSWBmhlrxM

Remington Garden | Answered on Sep 21, 2019


To change that trigger switch on a Remington saw, you need to open up the two handle halves and expose the switch. The wires are just "poked" into the switch, so you can make a tool to release them. I used a 1/16" diameter short length of wire and flattened about a 1/2" of it on an anvil. Push it in next to the wire and the wire will pull out, wiggle the tool a bit and it will pull out too. Push the wires into the new switch and put it all back together.

The switch is probably a #077525S ...seen them out there for $8 to $15.

Remington... | Answered on Sep 13, 2019


No threads, it snaps in and can be snapped out if you are careful.

Remington... | Answered on Sep 13, 2019


Okay here is the Fix for the Remington Pole for the remington saw. Lowes has a plumbing part that will work as I just purchased it 12/2010 The part is by GENOA and its a 3/4" pvc Union and the threads match. Its Lowes part 98996 and its < $6.00

Remington... | Answered on Jul 23, 2019


1. Try a penetrating oil, like product "deep creep". WD-40 is not a penetrating oil, it is a water displacement oil. Proper penetrating oil should work. 2. Try soaking in house hold, distilled vinegar, the really cheap stuff. For a few hours, and try again.

Remington Garden | Answered on Jul 14, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Remington Experts

ray gallant

Level 3 Expert

68638 Answers

STEVE SPAM REMOVER

Level 3 Expert

35836 Answers

Tom Chichester

Level 3 Expert

56040 Answers

Are you a Remington Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...