Razor USA Toys - Answered Questions & Fixed Issues

I have the same issue with mine. Batterys check out fine.. i'm starting to suspect the motor??

If the battery is gone(bad), sometimes it will show fully charged (volts are good).. but it has no amperage to "push" the voltage... It takes amperage to make the drifter move... (time for a new battery)... they don't last long...

Do you own a multimeter to check the voltage output from the battery

you need to manualy center your servo and your tail blaids, ones you do this then you shouldnt need any trim

one or both of the batteries must be bad, lift the seat up the remove the screws that hold the compartment down and then you should be able to see the two batteries below there, first visually inspect the batteries to see if they look like they are bulging, then test each battery with a multimeter and make sure it is showing at least 12 volts, chances are one or both of the batteries will not show more than 12 volts

this unit may take several hours to charge correctly

yes sounds like the control module, you can always jump the batteries directly to the motor to make sure that the motor is ok

there isn't one, but there are fuses by the battery that can be replaced

Most likely a bad battery. Check out put voltage on all posts. If it's 12 Volts DC or more, then it should be ok, and you'll need to start looking in the wiring such as the speed control switch. If not, your problem is a bad battery cell and you should replace it. NEVER TRY TO SERVICE A BATTERY!!!!!

at least 24 volts, usually a little more

check it with a multimeter and make sure that its putting out the correct amount of volts, it should be at least 24 volts

under the seat you have to remove the screws that hold the compartment on then this will give you access to the batteries and the fuse

check the charger end with a multimeter and make sure that its showing that its putting out the correct voltage

there is an on/off switch right below the seat next to where you plug in the charger, then you have to twist the right hand grip

did u figure out what happened, this just happened to me and i have no clue what it is

Very difficult: the wheel is hot pressed in there, on the shaft. To install a replacement wheel (if you can find separated one to begin with) you will need to heat the shaft and the slot on the wheel using an induction heater - you can't use an infrared or conduction heater because it would melt the material at the surface long before it would soften the core. Since this is a custom tool only the factory has it so you will have to improvise and that will not work too well, or for long.
Better just replace the entire transmission, it's cheap (less than $25) and you will only need a set of small screwdrivers. Beware, you will have to remove the splinter on the engine cog wheel completely before sliding it out.

Sounds like you are missing the central support rod or bar that connects the Babyweaver swinging crib to the stand, providing stability and support for the crib. This component is crucial for maintaining the structural integrity of the crib and ensuring safe usage. Here are some steps you can take to address the missing part: 1. Contact the Manufacturer: - Reach out to Babyweaver or the manufacturer of the swinging crib to inquire about obtaining a replacement central support rod. - Provide them with details about the missing part and the specific model of the swinging crib to ensure you receive the correct component. 2. Check for Spare Parts: - Check if the swinging crib came with a user manual or assembly instructions that may have information about spare parts or replacement components. - Look for any contact information provided for customer support or spare parts inquiries. 3. Online Search: - Conduct an online search using keywords such as "Babyweaver swinging crib central support rod" or "Babyweaver crib replacement parts" to see if you can find the specific part for purchase. - Explore baby product retailers, online marketplaces, and specialty stores that offer replacement parts for nursery furniture. 4. Local Retailers: - Visit local baby product stores or furniture stores that carry nursery items. - Bring the existing part (if you have one side of the support rod) to help them identify and match the missing component. 5. Custom Fabrication: - If you are unable to find a suitable replacement part, consider contacting a metal fabrication shop or a carpenter who may be able to custom-make a central support rod that fits your Babyweaver swinging crib. - Provide them with measurements and details about the required specifications for the part.

It sounds like the drop may have caused some internal damage to the electronics or wiring of the Teddy Ruxpin toy. Here are some steps you can take to try and troubleshoot the issue:

1. Restart the Toy: Sometimes a simple restart can resolve minor issues. Try turning off the toy completely, including any power switches or buttons, and then turning it back on again after a few moments.
2. Check Battery Compartment: Ensure that the batteries are properly inserted and making good contact with the terminals inside the battery compartment. If the drop caused any displacement of the batteries, it might affect the toy's functionality.
3. Inspect for Physical Damage: Carefully examine the exterior of the toy for any signs of physical damage, such as cracks, dents, or loose parts. If there's visible damage, it may indicate internal damage as well.
4. Test with Different Devices: If the Teddy Ruxpin toy connects to a separate app or device for sound playback, try connecting it to a different device to see if the issue persists. This can help determine if the problem lies with the toy or the connected device.
5. Contact Customer Support: If none of the above steps resolve the issue, it's possible that the drop caused internal damage to the toy's electronics or wiring. In this case, you may need to contact the manufacturer's customer support for assistance. They may be able to provide further troubleshooting steps or offer a repair or replacement option.

Keep in mind that since the toy is relatively new, it may still be under warranty, which could cover repairs or replacements for damage caused by accidents like drops. Be sure to check the warranty information or contact the manufacturer for guidance on warranty coverage.

I was able to find you this website with all kinds of great craft kits for pre-kindergarteners.

This game is a great one to play with kids on a wet afternoon stuck indoors. Basically use their toys to turn an area of the house into a toy store. Get the kids involved in choosing the games they would like to 'sell'. Write prices lists and stick them somewhere that the kids can see and reach ie Lego sets - $4, Dolls - $2

If you don't have any pretend money, you can make your own with the kids, then divide up the tasks and let them enjoy many hours of pretend shopping.