Raypak Logo

Raypak Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 163 Products
  • 1K Answers

That model is obsolete. HP means high pressure, there is a switch on the discharge side of the pump that is tripped and it wont allow the unit to come on.

Raypak Pool &... | Answered on May 28, 2020

I have a 93 crysler lebaron convertible I put a new battery in car and water in the radiator .but as much as we put it in it blows back out but dont no where it gos . A friend of mine messed with the fuel pump relay button .but it still dont start .the oil has a film in it .please I dont no what is wrong

Raypak HEADER... | Answered on May 09, 2020

possible shorted control board or bad ignitor

Raypak Pool &... | Answered on May 01, 2020

Heater cool down is very important and needs to be done. A time clock with a firemen switch is how it is normally done. Never run a heater with out water flowing thru it.

Raypak Pool &... | Answered on May 01, 2020

All fine that the thermostat clicks when tuned, However just check the contact for Voltage as the contacts do get burnt at times, thus your element is not getting sufficient voltage

Raypak Pool &... | Answered on May 01, 2020

This is very common with Raypak. What you hear is the way the air flow drafts through the heater. Raypaks typically draft very well. The rise of the heat off the burners draws in fresh air at the bottom and sides of the heater through the louvers and expels out the top.
You need the right mixture of fuel and oxygen for efficient burn and proper draft. A week flame or inefficient fresh air and the heater will not draft properly. A 406 is a very big heater my initial reaction is to check the gas supply. My assumption is the gas line may be undersized, especially if this heater was recently installed in place of a smaller unit. If the gas line is undersized the heater may operate but in time the insides will soot like a chimney and also change the dynamics of the way it drafts. Soot can also be a fire hazard so it is worth having a professional take gas pressure readings.

Raypak Pool &... | Answered on Jun 20, 2019

If unit on controller make sure heater set all the way up let controller control heat if display wont go higher possible bad board

Raypak Pool &... | Answered on Jun 15, 2019

if millivolt and gas to pilot replace pilot generator assembly or check for blocked line if electronic check ignitor or heater element

Raypak Pool &... | Answered on Mar 14, 2019

unit will screw in or out for more pressure or less

Raypak Pool &... | Answered on Aug 11, 2018

replace temp sensor at header and wires to board

Raypak Pool &... | Answered on Aug 04, 2018

lower by burner rack follow silver tube from gas valve to ignitor

Raypak Pool &... | Answered on Jul 16, 2018

check amazon about 200 dollars but clean burner tubes and check gas pressure it over heated

Raypak Pool &... | Answered on Jul 04, 2018

if using a controller see if heat is enabled and control is calling for heat if no control check safety circuit and temp sensor

Raypak Pool &... | Answered on Jun 23, 2018

see if voltage to ignitor when this happens if no voltage bad board also check gas pressure might be running out that's why it turns off

Raypak Pool &... | Answered on Jun 19, 2018

temp sensor bad

Raypak 010104... | Answered on Jun 13, 2018

check gas pressure and safety circuit then ignitor sns means temp sensor bad

Raypak Free... | Answered on Jun 10, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Raypak Experts

Bill Jordan

Level 2 Expert

375 Answers

Paul Carew

Level 3 Expert

3512 Answers

Tom Chichester

Level 3 Expert

56001 Answers

Are you a Raypak Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides