Pride Mobility Products Health & Beauty - Page 5 - Recent Questions, Troubleshooting & Support
Beep code 5.. wont move
hi Taffie, that related to the freewheel lever or brake
make sure the at the lever is not bent and make sure connection to the brake are okay , there is a micro-switch located on the brake make sure that's releasing when you move the lever... it like a rounded plastic point , that is part of the switch and sometimes they stick so acting like it 's in freewheel when in fact it isn't ...
Regards
Rob
How to unlock Jazzy Select chair so it can start up and run
Turn on the PWC
Push the joystick forward and hold for 2 seconds or until you hear a chirp.
Push the joystick backward and hold for 2 seconds or until you hear a chirp.
Release and there should be a long beep tone, signaling that it is unlocked. Since there are different joystick controllers on these chairs and I don't know exactly which one you have this is my best guess.
I have a Pride Celebrity. Where is the serial
Hello.i love to help.but am learning.who is not we learn something new every day.Please try visiting the makers website and ask or ring them.i hope this has helped,i have a scooter myself Colin.
Battries fully charged, turn key on and only beeps 5 times. Thats all.
hi Hal, that is a issue around based the brake or connectors to the brake or the micro-switch that is moved when you move the drive , freewheel lever.. ... firstly make sure the scooter is in drive mode and not free-wheel mode ., where the axle comes apart you will see a number of connectors , make sure they are a good fit ...
Update me please...
Regards
Rob
Why won't my scooter freewheel?
If the brake release lever is not working by this I mean the lever will not move the release position, this could be a case of the brake mechanism has seized up due to water or that sand and grit has got in the brake jamming it.
Try a spray of WD40 on the bake lever mechanism and work the lever back and forth. Failing that brake will need to be replaced.
How long does it take to fully charge a wheelchair batteries
If the batteries were discharged completely, the battery charger isn't strong enough to start the charging process. Take the batteries out and charge each one separately with an automotive type battery charger that is NOT automatic. This may take a day to recover this way. When the battery shows over 10 volts with a dc voltmeter you can re install them in the chair to complete the charge with the 24 volt charger. If the batteries have any amount of age past 2 years, it's time for new batteries.
AXS Mobility scooter loses battery power quickly.
hi , two problems can cause this,
1. batteries are weak, is the charger ok ? just because it 's green does not mean the charger is ok, can you validate the charge, try some other batteries ?,
2. Brake be activated or on at all times,
The best way to prove this is to remove the brake mech from the side of the motor completey now try the scooter, if the problem goes away then check the resistance of the brake, is it open or shorted ?
If you feel the brake, batteries and charger are working ok then the controller must be activating the brake and this is the fault but please double check the voltage on the brake leads.
Regards
GeWiz.
Lights work no power
Check you're freewheel lever if its in freewheel u have to take the key out engage lever & put key back in. Also if u have left the key on for more than twenty minutes the circuit will shut down only the light will work. take key out for 5 minutes then put it back it should work unless it's another problem good luck
How to remove throtter pot?
hi have u checked the reset button if this has tripped the scooter wont go give it a push its below the seat....also if u leave the key on for more than 20 minutes the circuit will shut down to fix this remove key then replace key & turn it on ..good luck
Troubleshooting code beeps 9 times. battery is charged and the unit is not hot.
hi, okay that a system controller fault however it can also be a loose connection around the controller area, removing the connectors that go into the controller has worked for me, if not it's normally a resistor network inside the controller.
I offer a free testing and repair service ...
Regards
Rob
www.gewizrepairs.co.uk
Why does my scooter have very little power
hi , have you checked the charger ? try another charger if possible, how old are the batteries and how long have they been left without charging ?
Regards
Rob
www.gewizrepairs.co.uk
Not finding what you are looking for?